manualshive.com logo in svg

CASTOR Y057, Руководство по обслуживанию на месте

Поделиться
Скачать
CASTOR Y057 Скачать руководство пользователя страница 34

Waveform Download and Fan Calibration

After replacing Ballast, main board, blower or upgrade firmware, please follow steps as below:

1.

Plug in power cord.

2.

Press and hold the [Up] button and then press the [Power] button once.

3.

Release the [Up] button after the [Temp] LED begins flashing.

4.

After a moment, the projector will turn on automatically.

5.

Wait a moment, enter the Service Mode by pressing the buttons sequentially as follows;

• Power > Left >Left > Menu

6.

Select “Factory Fan RPM” on the service menu and press “Menu” button. The picture as
shown below will appear. Check that the value of “Factory RPM” is within the range.

Color Wheel Index Adjustment

• After replacing main board, optical engine or upgrading firmware, the Color Wheel Index

Adjustment should be done.

Color wheel index adjustment procedure:

1.

Enter the Service Mode by pressing the buttons sequentially as follows:

• Power > Left > Left > Menu

2.

Select “Color Wheel Index” on the menu.

2. Replacement and Adjustment

32

Содержание Y057































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды