manualshive.com logo in svg

CASTLE TSM-21, Руководство по диагностике

Поделиться
Скачать
CASTLE TSM-21 Скачать руководство пользователя страница 40

 

5.18 Drill 

Solenoid 

Check 

 

      

 

21.51 

The Drill Solenoid controls air pressure to the Drive Cylinder, which provides the forward motion 

of the Drill’s boring stroke.  If the Drill Solenoid has stuck open, the drill will extend as soon as air 

is attached to the machine, regardless of whether the power is turned on.  If the Drill Solenoid is 

clogged the Drill may not start or complete the pilot hole. 

 

The appearance of the solenoids may differ. See Appendix E, page 51 for equivalent illustration 
for machines SN: 61076 and above. 

 

5.18.1 

TESTING STEPS: 

1. 

Detach the air supply from the machine.  

2. 

Swap the "Air Out" lines between the Drill Solenoid and the Router Solenoid. 

See Fig 20

. 

 

Pilot Valve, up to 

sn:61076 

Clamp Exhaust 

Clamp Solenoid 

Router Solenoid 

Drill Solenoid 

Air OUT lines 

Regulator Knob 

Air IN lines 

Router Feed Rate knob 

Fig 20 

Castle Inc 

TSM-21 Diagnostic Manual v2 

Page 40 of 63 

 

Содержание TSM-21
































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды