2220-5
Using the Viewer Screen
The press of a button in the Timekeeping Mode displays the Viewer Screen,
which you can use to view images stored in memory.
Important!
•
The watch does not emit any alarm, Hourly Time Signal, or Countdown Alarm
sound while the Viewer Screen is on the display. Instead, the message ALM
flashes in the upper left corner of the display when an alarm time is reached,
and the message TMR flashes when the countdown reaches zero.
To display the Viewer Screen
1. In the Timekeeping Mode, press
E
or
B
to display the image that was on the
display the last time you exited the Viewer
Screen or the VISUAL DATABANK Mode.
2. Use
E
(+) and
B
(–) to scroll through the
images in memory.
•
Holding down either button scrolls at high
speed.
•
Hold down
C
to view the recording date
and time of the displayed image, and text
attached to the image, if there is any.
•
The image may appear somewhat dark
while recording date and time (and attached
text, if any) are on the display.
3. To close the Viewer Screen and return to
the Timekeeping Mode display, press
D
.
•
The watch automatically exits the Viewer
Screen if you do not perform any operation
for about 15 seconds.
To adjust image contrast
1. In the Timekeeping Mode, press
E
or
B
to display the Viewer Screen.
2. Press
A
to display the current image contrast setting value in the upper
left corner of the display.
3. Use
B
(darker) and
E
(lighter) to adjust the contrast to any one of the
15 available levels.
4. After the contrast setting is the way you want, press
A
to apply the
setting and exit the setting screen.
Note
•
The above procedure affects the contrast of images only. See “Contrast
Adjustment” for information about adjusting the contrast of other screens.
ABE KEIKO
012-034-5678
2000. 6.30.
PM 10:05
Text
Recording date
and time
AL2
A
12:‰‰
OFF
Alarm time
(Hour : Minutes)
Alarm name
(Alarm 2)
AL2
A
12:‰‰
ON
ALARM MODE
You can use the Alarm Mode to set five
independent alarms. You can also turn on an
Hourly Time Signal that causes the watch to
beep every hour on the hour.
Important!
•
The watch does not emit any alarm or
Hourly Time Signal sounds while it is in the
Camera Mode, VISUAL DATABANK Mode,
or IR Mode, or while the Timekeeping
Mode’s Viewer Screen is on the display.
•
In the case of the VISUAL DATABANK
Mode and Viewer Screen, the message
ALM flashes in the upper left corner of the
display when an alarm time is reached.
To set the alarm time
1. In the Alarm Mode, use
E
(+) and
B
(–) to display the screen for the
alarm whose time you want to set.
Alarm 1
(AL1)
Alarm 2
(AL2)
Alarm 5
(AL5)
Alarm 4
(AL4)
Alarm 3
(AL3)
Hourly Time Signal
(SIG)
2. After you select an alarm, hold down
A
until the hour digits of the alarm time start
to flash on the display.
•
The hour digits are flashing because they
are
selected.
•
This operation automatically turns on the
alarm.
The on/off
status of each
alarm is
indicated here.
Hourly time
Signal on
indicator
Alarm on indicator
3. While the hour setting is flashing, use
E
(+) and
B
(–) to change it.
•
Holding down either button changes the setting at high speed.
•
When setting the alarm time using the 12-hour format, take care to set the
time correctly as am (A indicator) or pm (P indicator).
4. Press
D
so that the minute digits of the alarm time start to flash.
•
Each press of
D
moves the flashing between Hour and Minutes.
5. While the minutes setting is flashing, use
E
(+) and
B
(–) to change it.
•
Holding down either button changes the setting at high speed.
6. Press
A
to exit the setting screen.
Note
•
The watch automatically exits the setting screen if you do not perform any
operation for about two minutes.
Daily Alarm Operation
The alarm sounds at the preset time each day for about 20 seconds, or until
you stop it by pressing any button.
To test the alarm
In the Alarm Mode, hold down
C
to sound the
alarm.
To turn a daily alarm and the Hourly
Time Signal on and off
1. In the Alarm Mode, use
E
(+) and
B
(–)
to display an alarm screen or the Hourly
Time Signal screen.
2. When the alarm or Hourly Time Signal you
want is selected, press
C
to turn it on and
off.
•
The alarm on indicator and the Hourly Time
Signal on indicator are shown on the display
in the Timekeeping, Alarm, Countdown
Alarm, and Stopwatch Modes.
•
If any alarm is on, the alarm on indicator is
shown on the display.
COUNTDOWN ALARM MODE
The Countdown Alarm Mode lets you set a start time of up to 60 minutes. A
Countdown Alarm sounds when the countdown reaches zero.
Important!
•
The watch does not emit the Countdown Alarm sound while it is in the
Camera Mode, VISUAL DATABANK Mode, or IR Mode, or while the
Timekeeping Mode’s Viewer Screen is on the display.
•
In the case of the VISUAL DATABANK Mode and Viewer Screen, the
message TMR flashes in the upper left corner of the display when the end
of the countdown is reached.
To set the countdown start time
1. In the Countdown Alarm Mode, hold down
A
until the minutes setting of the
countdown alarm start to flash.
2. While the minutes setting is flashing, use
E
(+) and
B
(–) to change it.
•
Holding down either button changes the
setting at high speed.
3. Press
A
to exit the setting screen.
Note
•
The watch automatically exits the setting screen if you do not perform any
operation for about two minutes.
Using the Countdown Alarm
•
Each press of
E
starts and stops the
countdown.
•
The time is counted down on the display in
one-second increments.
•
Pressing
B
while a countdown is stopped
resets the countdown to the countdown start
time.
•
When the countdown reaches zero, an
alarm sounds for about 10 seconds or until
you stop it by pressing any button.
TMR
6‰ '‰‰
TMR
2 '59
Seconds
Minutes
AL2
A
12:‰‰
ON
