Operation Guide 5481
E-39
Alarm indicator
Hourly time signal indicator
To stop the alarm
Press any button.
E-38
To test the alarm
In the Alarm Mode, hold down
D
to sound the alarm.
To turn an alarm and the Hourly Time Signal on and off
1. In the Alarm Mode, use
D
to select an alarm or the Hourly Time Signal.
x
Each press of
D
cycles between the alarm time screen and the hourly time
signal
SIG
setting screen.
2. Press
A
to toggle the displayed setting (alarm or hourly time signal) between
on and off.
x
An alarm on indicator will be on the display whenever any one of the fi ve alarms
is turned on. Turning on the hourly time signal causes its indicator to appear on
the screen.
E-37
3. Hold down
A
for about two seconds until the alarm time starts to fl ash. This is
the setting mode.
x
The hour and minute hands automatically move out of the way at this time (page
E-12).
4. Press
C
to move the fl ashing between the hour and
minute settings.
5. While a setting is fl ashing, use
D
(+) and
B
(–) to
change it.
6. Press
A
to exit the setting mode.
Note
x
If you do not perform any operation for about two
or three minutes in the Alarm Mode, the watch will
automatically return to the Timekeeping Mode.
Alarm time hour
E-36
Using the Alarm
You can set up to fi ve different alarms.
The watch beeps for about 10 seconds when the alarm
time is reached. The hourly time signal causes the watch
to beep every hour on the hour.
To set an alarm time
1. Use
C
to navigate to the alarm mode (page E-11).
2. Press
D
to display the setting (
AL1
through
AL5
, or
SIG
) you want to change.
AL1
D
AL2
D
AL3
D
D
SIG
D
AL5
D
AL4
E-35
To perform a countdown timer operation
D
D
D
D
A
Start
Stop
(Resume)
(Stop)
Reset
x
Before starting a countdown timer operation, check to make sure that a
countdown operation is not in progress (indicated by the seconds counting down).
If it is, press
D
to stop it and then
A
to reset to the countdown start time.
To stop the alarm
Press any button.
E-34
To confi gure the countdown timer
1. Hold down
A
for about two seconds until the hour
digits of the start time start to fl ash.
x
Press
C
to toggle the fl ashing between the hours
and minutes.
x
The hour and minute hands automatically move out of
the way at this time (page E-12).
x
If the countdown start time is not displayed, use the
procedure under “To perform a countdown timer
operation” (page E-35) to display it.
2. Use
D
and
B
to change the setting of the fl ashing digits (hours or minutes).
x
You can set a start time in the range of 1 minute to 24 hours in 1-minute
increments.
3. Press
A
to exit the setting mode.
E-33
Countdown Timer
The countdown timer can be set within a range of
one minute to 24 hours. An alarm sounds when the
countdown reaches zero.
To enter the Countdown Timer Mode
Use
C
to select the Countdown Timer Mode as shown
on page E-11.
Seconds
Minutes
Hours
E-32
Note
x
You can use the above operation only while the stopwatch is reset to all zeros.
−
If the result of a stopped or ongoing timing operation was left on the display the
last time the Stopwatch Mode was exited, pressing
D
above will display that
stopped or ongoing stopwatch operation.
E-31
Starting the Stopwatch while in the Timekeeping Mode
Use the procedure below to start a stopwatch elapsed time measurement while in
the Timekeeping Mode.
In the Timekeeping Mode, press
D
.
D
E-30
Note
x
The Stopwatch Mode can indicate elapsed time up to 59 minutes, 59.99 seconds.
x
Once started, stopwatch timing continues until you press
D
to stop it, even if
you exit the Stopwatch Mode to another mode and even if timing reaches the
stopwatch limit defi ned above.
x
Exiting the Stopwatch Mode while a split time is frozen on the display clears the
split time and returns to elapsed time measurement.
