Operation Guide 3160
2
To view the time in another city
While in the World Time Mode, use the
D
to scroll through the city codes (time zones).
•
Pressing the
D
and
B
at the same time will jump to the UTC time zone.
To toggle a city code time between Standard Time and Daylight Saving Time
1. In the World Time Mode, use
D
to display the city code
(time zone) whose Standard Time/Daylight Saving Time
setting you want to change.
2. Hold down
A
to toggle between Daylight Saving Time
(
DST
indicator displayed) and Standard Time (
DST
indicator not displayed).
•
The
DST
indicator is shown on the World Time Mode
screen while Daylight Saving Time is turned on.
•
Note that the Standard Time/Daylight Saving Time
setting affects only the currently displayed city code.
Other city codes are not affected.
•
Note that you cannot switch between Standard Time
and Daylight Saving Time while UTC is selected as the
city code.
DST indicator
l l l l
l
lll
ll
ll
ll
ll
ll
l l l l
Alarms
The Alarm Mode gives you a choice of four one-time
alarms and one snooze alarm.
Also use the Alarm Mode to turn the Hourly Time Signal
(
SIG
) on and off.
•
There are five alarm screens numbered
AL1
,
AL2
,
AL3
and
AL
4
for the one-time alarm, a snooze alarm
screen indicated by
SNZ
. The Hourly Time Signal
screen is indicated by
SIG
.
•
All of the operations in this section are performed in the
Alarm Mode, which you enter by pressing
C
.
Alarm time
(Hour : Minutes)
Alarm number
To set an alarm time
1. In the Alarm Mode, use
D
to scroll through the alarm
screens until the one whose time you want to set is
displayed.
•
To set a one-time alarm, display an alarm screen
AL1
,
AL2
,
AL3
and
AL
4
.
To set the snooze alarm, display the
SNZ
screen.
•
The snooze alarm repeats every five minutes.
2. After you select an alarm, hold down
A
until the hour setting of the alarm time
starts to flash, which indicates the setting screen.
•
This operation turns on the alarm automatically.
3. Press
C
to move the flashing between the hour and minute settings.
4. While a setting is flashing, use
D
(+) and
B
(–) to change it.
•
With the 12-hour format, set the time correctly as a.m. or p.m. (
P
indicator).
5. Press
A
to exit the setting screen.
Alarm Operation
The alarm tone sounds at the preset time for 10 seconds, regardless of the mode the
watch is in. In the case of the snooze alarm, the alarm operation is performed a total
of seven times, every five minutes, until you turn the alarm off.
•
Alarm and Hourly Time Signal operations are performed in accordance with the
Timekeeping Mode time.
•
To stop the alarm tone after it starts to sound, press any button.
•
Performing any one of the following operations during a 5-minute interval between
snooze alarms cancels the current snooze alarm operation.
Displaying the Timekeeping Mode setting screen
Displaying the
SNZ
setting screen
To test the alarm
In the Alarm Mode, hold down
D
to sound the alarm.
To turn an alarm on and off
1. In the Alarm Mode, use
D
to select an alarm.
2. Press
A
to toggle it on and off.
•
Turning on a alarm (
AL1
,
AL2
,
AL3
,
AL
4
or
SNZ
) displays the alarm on indicator (
) on its Alarm
Mode screen.
•
In all modes, the alarm on indicator is shown for any
alarm that is currently turned on.
•
The alarm on indicator flashes while the alarm is
sounding.
•
The snooze alarm indicator (
) flashes while the
snooze alarm is sounding and during the 5-minute
intervals between alarms.
Alarm on
indicator
ON
Snooze
alarm
indicator
To turn the Hourly Time Signal on and off
1. In the Alarm Mode, use
D
to select the Hourly Time
Signal (
SI
G
).
2. Press
A
to toggle it on and off.
•
The Hourly Time Signal on indicator (
) is shown on
the display in all modes while this function is turned on.
Hourly time signal
on indicator
Stopwatch
The stopwatch lets you measure elapsed time, split times,
and two finishes.
•
The display range of the stopwatch is 23 hours, 59
minutes, 59.99 seconds.
•
The stopwatch continues to run, restarting from zero
after it reaches its limit, until you stop it.
•
The stopwatch measurement operation continues even
if you exit the Stopwatch Mode.
•
Exiting the Stopwatch Mode while a split time is frozen
on the display clears the split time and returns to
elapsed time measurement.
•
All of the operations in this section are performed in the
Stopwatch Mode, which you enter by pressing
C
.
Hours
Minutes
Seconds
1/100 second
To measure times with the stopwatch
Elapsed Time
Split Time
Two Finishes
D
Start
D
Start
D
Start
Stop
Re-start
Stop
D
D
D
Split
(
displayed)
Split release
Stop
A
D
A
Split
First runner finishes.
Display time of first
runner.
Stop
Second runner
finishes.
Split release
Display time of
second runner.
D
A
A
A
A
A
➤
➤
➤
➤
➤
➤
➤
➤
➤
➤
➤
➤
Clear
Clear
Clear
Countdown Timer
You can set the countdown timer within a range of one
minute to 24 hours. An alarm sounds when the countdown
reaches zero.
•
All of the operations in this section are performed in the
Countdown Timer Mode, which you enter by pressing
C
.
Configuring the Countdown Timer
The following are the settings you should configure before
actually using the countdown timer.
Countdown start time
•
See “To configure the countdown timer” for information
about setting up the timer.
Hours
Minutes
Seconds
Countdown End Beeper
The countdown end beeper lets you know when the countdown reaches zero. The
beeper stops after about 10 seconds or when you press any button.
To configure the countdown timer
1. While the countdown start time is on the display in the
Countdown Timer Mode, hold down
A
until the current
countdown start time starts to flash, which indicates the
setting screen.
•
If the countdown start time is not displayed, use the
procedure under “To use the countdown timer” to
display it.
2. Press
C
to move the flashing in the sequence shown
below to select other settings.
Hours
Minutes
ll
ll
lll
ll
l
ll
ll
3. When the setting you want to change is flashing, use
D
and
B
to change it as
described below.
Button Operation
Use
D
(+) and
B
(–) to change the setting.
Setting
Hours, Minutes
Screen
ll
l
llll
ll
llll
l
Current timer
time
Timer start time
•
To specify a countdown start time of 24 hours, set
.
4. Press
A
to exit the setting screen.
To use the countdown timer
Press
D
while in the Countdown Timer Mode to start the
countdown timer.
•
The countdown timer operation continues even if you
exit the Countdown Timer Mode.
•
Press
D
while a countdown operation is in progress to
pause it. Press
D
again to resume the countdown.
•
To stop a countdown operation completely, first pause it
(by pressing
D
), and then press
A
. This returns the
countdown time to its starting value.
Illumination
This watch has an EL (electro-luminescent) panel that
causes the entire display to glow for easy reading in the
dark. The watch’s auto light switch turns on illumination
automatically when you angle the watch towards your
face.
•
The auto light switch must be turned on (indicated by
the auto light switch on indicator) for it to operate.
•
See “Illumination Precautions” for other important
information about using illumination.
To illuminate the display manually
In any mode, press
B
to turn on illumination.
•
The above operation turns on illumination regardless of
the current auto light switch setting.
Auto light switch
on indicator
About the Auto Light Switch
Turning on the auto light switch causes illumination to turn on, whenever you position
your wrist as described below in any mode.
Moving the watch to a position that is parallel to the ground and then tilting it towards
you more than 40 degrees causes illumination to turn on.
•
Wear the watch on the outside of your wrist.
Parallel to
ground
More than
40°
