Operation Guide 5478
E-39
To stop the alarm
Press any button.
E-38
To perform a countdown timer operation
E
E
E
E
D
Start
Stop
(Resume)
(Stop)
Reset
Countdown in Progress
Dial hand: Moves from right to left.
E-37
To configure the countdown timer
x
If a countdown timer operation is in progress, press
E
to pause it and then press
D
to reset the target time to
its start time.
x
If a countdown timer operation is paused, press
D
to
reset the timer to its start time.
1. Hold down
A
until the flashing
SET Hold
indicator
disappears from the display and the minutes digits
start to flash. Release
A
after the digits start to flash.
2. Use
D
(+) and
B
(–) to change the minutes setting.
x
Holding down either button scrolls at high speed.
3. After all the settings are the way you want, press
A
to
exit the setting screen.
E-36
Countdown Timer
The countdown timer can be set within a range of
one minute to 60 minutes. An alarm sounds when the
countdown reaches zero.
To enter the Countdown Timer Mode
Use
C
to select the Countdown Timer Mode as shown
on page E-12.
Minutes
Seconds
Seconds
1/10 second
E-35
Note
x
TARGET
flashes in the above operation even if the watch is in another mode.
To stop the alert beeper
Pressing any button while the alert beeper is sounding will stop it.
x
Pressing
D
or
E
operates the elapsed time operation on page E-28.
To perform stopwatch timing without using the Target Time Alarm
Use step 7 under “To set a target time” to disable the target time alarm.
E-34
(3) Target time reached
x
Beep for 10 seconds.
x
Screen: Changes as shown in the figure.
x
TARGET
becomes unlit.
(4) After target time is expired
x
Screen: Rightmost indicator that indicates minutes flashes (at slow speed).
x
Elapsed time is measured, with
TARGET
remaining unlit.
x
Resetting the elapsed stopwatch time automatically causes
TARGET
to re-
appear. You can re-use the same target time, if you want.
E-33
(2) From target time half until target time is reached
x
Screen: As shown in the figure, all of the part that
indicates minutes flashes.
x
TARGET
flashes at high speed starting from one
minute before the target time.
E-32
x
You can get an idea of time elapsed until the target time from changes in the
display.
(1) From start up to half of target time
x
Screen: As shown in the figure, rightmost indicator that
indicates minutes flashes.
x
TARGET
starts to flash.
E-31
7. Press
D
to toggle the target time alarm between on and off.
x
TARGET
is displayed while the target time alarm is on, and not displayed while
it is off.
8. After all the settings are the way you want, press
A
to exit the setting screen.
To use the target time alarm
1. Reset the stopwatch to all zeros and then press
E
.
This will cause
TARGET
to flash on the display.
2. Now you can perform the same operations as those in the steps on page E-28.
(1)
(2)
(4)
(3)
Start
Target time
E-30
To set a target time
1. Reset the stopwatch to all zeros.
2. Hold down
A
until the flashing
SET Hold
indicator
disappears from the display and the hour digit starts to
flash. Release
A
after the hour digit starts to flash.
3. Use
D
(+) and
B
(–) to change the hour setting.
x
Holding down either button scrolls at high speed.
x
For a target time of 24 hours, set 00 hours
00 minutes.
4. Press
C
to switch to the minutes setting.
5. Use
D
(+) and
B
(–) to change the minutes setting.
x
Holding down either button scrolls at high speed.
6. Press
C
to display the target time alarm on/off setting.
Hours
Target Time operation in
progress