Operation Guide 5245
E-49
The watch is returning to the Timekeeping Mode automatically from the Alarm Mode
x
(page E-43).
■
Hands suddenly stop moving. Button operation also is disabled.
The watch may be in the power recovery mode (page E-12). Do not perform any
operation until the hands return to their normal positions (in about 15 minutes). The
hands should return to their correct positions when normal operation returns. To help
power recover, leave the watch in a location where it is exposed to light.
■
The current time setting is off by hours.
Your Home City setting may be wrong. Check your Home City setting and correct it, if
necessary (page E-20).
■
The current time setting is off by one hour.
Use the procedure under “To toggle the Home City time between standard time and
daylight saving time” (page E-22) to change the
STD
/
DST
setting.
E-48
Troubleshooting
Hand Movement and Position
■
I lost track of what mode the watch is in.
Refer to “To select a mode” (page E-18). To return directly to the Timekeeping Mode
from any other mode, hold down
C
for about two seconds.
■
The
x
Second Hand
is moving at two-second intervals.
■
All the watch’s hands are stopped at 12 o’clock and none of the buttons work.
Power may be low. Expose the watch to light until the
x
Second Hand
starts moving
normally, at one-second intervals (page E-10).
■
The hands of the watch suddenly start moving at high speed, even when I do
not perform any operation.
This could be due to any one of the following causes. In all cases, the hand movement
does not indicate malfunction, and should stop shortly.
The watch is recovering from a sleep state (page E-14).
x
E-47
After confi rming that the
5.
b
Left Dial Hands
are in the
correct home positions, press
C
. This will advance to
n
Right Dial Hand
home position adjustment.
The
x
n
Right Dial Hand
is in the correct home position
if it is pointing at 12 o’clock. If it isn’t, use
D
(+) and
B
(–) to move it to 12 o’clock.
After confi rming that the
6.
n
Right Dial Hand
is in the
correct home position, press
C
. This will advance to
m
Day
home position adjustment.
The
x
m
Day
is in the correct home position if it
shows
1
. If it doesn’t, use
D
(+) and
B
(–) to change
the day to
1
.
Press
7.
A
to return to the Timekeeping Mode.
The
x
m
Day
moves to the current day, and then the
z
Hour Hand
and the
c
Minute Hand
move to the current time. Wait until everything stops moving.
6
5
*
E-46
After confi rming that the
3.
x
Second Hand
is at the proper home position, press
C
.
This will switch to
z
Hour Hand
and
c
Minute Hand
home position adjustment.
The
x
z
Hour Hand
and
c
Minute Hand
are at their proper home positions if
they both move to 12 o’clock. The
v
24-hour Hand
also will move along with
z
Hour Hand
movement, and cannot be adjusted individually. If the hands are
not positioned correctly, use
D
(+) and
B
(–) to move them to their proper
home positions.
After confi rming that the
4.
z
Hour Hand
and
c
Minute
Hand
are in their correct home positions, press
C
.
This will switch to
b
Left Dial Hands
home position
adjustment.
The
x
b
Left Dial Hands
are at their proper home
positions if they both move to 12 o’clock. If the hands
are not positioned correctly, use
D
(+) and
B
(–) to
move them to 12 o’clock.
B
+
*
>
E-45
The watch is now in the home position adjustment
x
mode.
The watch will exit the adjustment mode automatically
x
if you do not perform any operation for about two or
three minutes.
First is
x
x
Second Hand
home position adjustment.
If the
x
x
Second Hand
moves to 12 o’clock, it is in the
correct home position. If it doesn’t, use
D
to move it
to 12 o’clock.
Each press of
x
C
in the home position adjustment
mode will cycle through the adjustment settings as
shown below.
@
x
Second
z
Hour/
c
Minute/
v
24-hour
b
Left Dial Hands
n
Right Dial Hand
m
Day
C
C
C
C
C
E-44
Adjusting the Home Positions
Strong magnetism or impact can cause the hands and/or date of the watch to be off.
If this happens, perform the applicable home position adjustment procedures in this
section.
Note
Any time after you enter the home position adjustment mode in step 1 of the following
procedure, you can return to the Timekeeping Mode by pressing
A
. The watch also
will return to the Timekeeping Mode automatically if you do not perform any operation
for about two or three minutes in home position adjustment mode. In either case, any
adjustments you made before the watch returned to the Timekeeping Mode will be
applied.
To adjust the home positions
Hold down
1.
C
for about two seconds until the watch beeps twice and enters the
Timekeeping Mode.
Hold down
2.
D
for about three seconds until the watch beeps.
E-43
To change the alarm time setting
Use
1.
C
to move the
n
Right Dial Hand
to
ALM
.
Use
2.
D
(+) and
B
(–) to change the alarm time setting.
Each press of either button will move the
x
b
Left Dial Hands
one minute.
Holding down
x
D
or
B
will start high-speed hand movement in the applicable
direction. To stop high-speed hand movement, press any button.
The alarm always works based on the time kept in the Timekeeping Mode.
x
The watch will return to the Timekeeping Mode automatically if you do not
x
perform any operation in the Alarm Mode for about two or three minutes.
To turn the alarm on or off
In the Alarm Mode, press
A
to toggle the alarm on and off. The
x
Second Hand
will
indicate the current ON/OFF setting.
To stop the alarm
Press any button.
E-42
Using the Alarm
When the alarm is turned on, an alarm will sound for about 10 seconds each day
when the time in the Timekeeping Mode reaches the preset alarm time. This is true
even if the watch is not in the Timekeeping Mode.
Hand Functions
x
Second Hand:
Indicates the current alarm ON/OFF setting.
b
Left Dial Hands:
Indicate the current alarm time setting in 24-hour
format.
n
Right Dial Hand:
Points to
ALM
.
*
6
@
E-41
After swapping the Home City and World Time City, the watch will stay in the
x
World Time Mode. The
x
Second Hand
will point to your new World Time City
(
TYO
in this example).
The
x
b
Left Dial Hands
will indicate the current time in your new World Time City.
E-40
To swap your Home City and World Time City
In the World Time Mode, use
1.
D
to select the World Time City you want.
In this example, you would move the
x
x
Second Hand
to
NYC
in order to select New York as the World
Time City.
Wait until the
x
b
Left Dial Hands
complete their move
to the time in the currently selected World Time
City. You will not be able to perform step 2 of this
procedure until the hands stop moving.
Hold down
2.
B
for about three seconds until the watch
beeps.
This will make the World Time City (
x
NYC
in this
example) your new Home City. At the same time, it will
change the Home City you had selected prior to step 2
(
TYO
in this example), to your new World Time City.
@
*