Operation Guide 5196/5252/5301
E-39
Press
2.
A
twice.
The
x
x
Second Hand
will align with the bottom of the
v
Day Indicator
.
Rotate the crown to change the day setting.
3.
Important!
Note that you can change the day setting only by
x
advancing to the next day. You cannot go back to a
previous day. To change from 30 to 29, for example, you
must change the setting in the sequence 30
31
1 ...
29.
After the day setting is the way you want, press
4.
A
.
The
x
x
Second Hand
will move to the current month
setting.
>
@
E-38
To set the date manually
Pull the crown out to the second click.
1.
The
x
x
Second Hand
will move to
A
(
AM
) or
P
(
PM
) in accordance with the
current time.
Use
x
A
to cycle through the available
settings in the sequence shown below.
Hour and
minutes
AM/PM
Day
Year
(tens digit)
Month
Year
(ones digit)
A
A
A
A
A
A
@
>
E-37
Note
A high-speed movement feature (one hour maximum) is available when setting the
x
time. See “Crown Operations” (page E-5).
After the time setting is the way you want, press
3.
A
change to the AM/PM setting.
The
x
x
Second Hand
will move to
A
(
AM
) or
P
(
PM
).
Rotate the crown to move the
4.
x
Second Hand
to the AM/PM setting you want.
If you want to continue on to the date setting, press
x
A
and then perform the
procedure starting from step 3 under “To set the date manually” (page E-38).
At the top of a minute (based on the time signal on the radio, TV, etc.), push the
5.
crown back in to restart timekeeping.
The
x
x
Second Hand
will restart timekeeping from 0 seconds (12 o’clock).
E-36
To set the time manually
Pull out the crown to the second click.
1.
The
x
x
Second Hand
will move to
A
(
AM
) or
P
(
PM
) in accordance with the
current time.
Use
x
A
to cycle through the available
settings in the sequence shown below.
Hour and
minutes
AM/PM
Day
Year
(tens digit)
Month
Year
(ones digit)
A
A
A
A
A
A
While the hour and minutes setting is selected, rotate the crown to change the
2.
current time setting.
@
E-35
Push the crown back in.
3.
The
x
x
Second Hand
will perform movement that indicates whether the watch’s
battery requires charging. After that, regular timekeeping will resume. See “To
use the charging guide” (page E-18).
Confi guring Time and Date Settings Manually
You should confi gure time and date settings manually when you are in an area where
time calibration signal reception is not possible for some reason.
Important!
It is recommended that you allow the watch to make time and date adjustments
x
automatically when in an area where the time calibration signal is receivable.
E-34
To change the location setting
Pull out the crown to the fi rst click.
1.
The
x
x
Second Hand
will move to the currently
selected location.
Rotate the crown to move the
2.
x
Second Hand
to the location setting you want to use.
Important!
Leaving the crown pulled out for more than two
x
minutes without performing any operation will
automatically cause setting operation to become
disabled. If this happens, press the crown
back in and then pull it out again to confi gure
settings.
E-33
Setting the wrong location can make reception impossible or may result in incorrect
time settings. See “Radio Controlled Atomic Timekeeping” (page E-23).
Important!
When using this watch in China, set
x
CN
(
HKG
,
HONG KONG
) as the location.
To check the current location setting
Pull the crown out to the fi rst click.
1.
The
x
x
Second Hand
will move to the currently
selected location.
Push the crown back in.
2.
The
x
x
Second Hand
will perform movement
that indicates whether the watch’s battery
requires charging. After that, regular
timekeeping will resume. See “To use the
charging guide” (page E-18).
E-32
Confi guring Time and Date Settings
Normally time and date settings are confi gured automatically when a time calibration
signal is received in accordance with your location setting.
Important!
Whenever you are in an area where a signal cannot be received or if your location
x
setting does not support signal reception, you will need to confi gure time settings
manually. See “Confi guring Time and Date Settings Manually” (page E-35).
Location Setting
Select one of the location settings shown below in accordance with your current
location.
In China
CN (HKG, HONG KONG)
In Japan
JP (TYO, TOKYO)
Any other location
OFF (Receive off)
E-31
Radio-controlled Atomic Timekeeping Precautions
Strong electrostatic charge can result in the wrong time setting.
x
Even if a receive operation is successful, certain conditions can cause the time
x
setting to be off by up to one second.
The watch is designed to update the date automatically for the period January 1,
x
2000 to December 31, 2099. Updating of the date by signal reception will no longer
be performed starting from January 1, 2100.
If you are in an area where signal reception is not possible, the watch keeps time
x
with the precision noted in “Specifi cations” (page E-54).
The receive operation is disabled under any of the following conditions.
x
While the battery charge level is at Level 3 or lower (page E-16)
−
While the watch is in the function sleep state (power saving, page E-21)
−
E-30
To check the result of the latest receive operation
Press
1.
A
.
The
x
x
Second Hand
will indicate the result of the last
receive operation.
Y (YES)
Receive successful
N (NO)
Receive failed
Press
2.
A
to return to regular timekeeping. Regular
timekeeping also will resume if no operation is
performed for about fi ve seconds.
Note
The
x
x
x
Second Hand
will indicate
N
(
NO
) if you have
adjusted the time setting manually since the latest
receive operation.
@