Operation Guide 3440 3441
E-20
To position the lap time and split time on the display
Each press of
A
cycles the lap time and split time positions in the sequence shown
below.
•
You can perform the above operation while stopwatch operation is ongoing or
stopped.
Lap time
Lap time
Hours
Seconds
Minutes
Split time
Split time
Hours
Seconds
Minutes
Split time
Lap time
Remaining memory
E-21
More than 10 hours
•
Whenever the elapsed time exceeds 10 hours, the measurement changes from
1/100-second units to 1-second units.
E-22
Recall Mode
Use the Recall Mode to recall and delete records stored
by the Stopwatch Mode.
•
Stopwatch records are stored in “logs” that are created
automatically by the watch. See “Memory Management”
on page E-48 for more information.
•
The title screen of the newest log appears fi rst
whenever you enter the Recall Mode.
•
Log numbers are automatically assigned in sequence,
starting from
.
•
All of the operations in this section are performed in the
Recall Mode, which you enter by pressing
C
(page E-9).
To recall stopwatch records
In the Recall Mode, use
A
to scroll through the log title
screens, starting from the newest one, as shown below.
When the title screen of the log you want is displayed, use
D
(+) and
B
(–) to cycle through the records contained
in the log.
Creation date
(Month – Day)
Log number
Time measurement
was performed
Log Title Screen
E-23
Stopwatch Record
Screen
Best Lap Time
Screen
Lap/Split number
Lap time
BEST indicator
Split time
Log Title Screen
E-24
•
The locations of the lap time and split time in the Stopwatch Record screen are
determined by the display format you last selected in the Stopwatch Mode (page
E-17).
•
The BEST indicator identifi es the record that contains the best lap time in the log.
•
If a best lap time record is deleted automatically when the log becomes full, the
BEST indicator will not be transferred to the record with the next best lap time. See
“Memory Management” on page E-48 for more information about automatic deletion
of records.
To delete a log
1. In the Recall Mode, display the title screen or one of the records of the log you want
to delete.
2. While holding down
B
, hold down
D
for about two seconds until the watch beeps.
•
“
CLR
” will fl ash on the display for two seconds and then the watch will beep.
Release
B
and
D
at this time.
•
You cannot delete the log of an ongoing elapsed time measurement operation.
E-25
To delete all logs
While holding down
B
, hold down
D
for about fi ve seconds until the watch beeps
once and then a second time.
•
“
CLR
” will fl ash on the display for two seconds and then the watch will beep once.
Keep
B
and
D
depressed and “
ALL
” will fl ash on the display for three seconds,
and then the watch will beep again. This indicates that all log data is cleared.
•
You cannot delete logs while an elapsed timing operation is in progress.
E-26
Countdown Timer
Dual timers can be set with two different starting times.
The watch can be confi gured so the two timers alternate,
so when one reaches the end of its countdown, the other
timer starts. You can specify a “number of repeats” value,
which controls how many times the two-timer countdown
operation is performed (1 = once, 2 = twice, etc.). The
starting time of each timer can be set in fi ve-second steps
up to 99 minutes, 55 seconds.
You can specify up to 10 repeats. The watch emits a short
beep whenever either of the timers reaches the end of its
countdown during an ongoing timer operation. The watch
emits a 5-second beep when the end of the fi nal timer
operation (specifi ed by the number of repeats) is reached.
Countdown End Beeper
The countdown end beeper lets you know when the countdown reaches zero. The
beeper stops after about 5 seconds or when you press any button.
Number of Repeats
Seconds
Timer 1
Minutes
E-27
To confi gure the countdown timer
1. While the countdown start time is on the display in the
Countdown Timer Mode, hold down
A
until the current
countdown start time starts to fl ash, which indicates the
setting screen.
•
If the countdown start time is not displayed, use
the procedure under “To use the countdown timer”
(page E-29) to display it.
2. Press
C
to move the fl ashing in the sequence shown
below to select other settings.
Timer 1
Minutes
Timer 1
Seconds
Timer 2
Minutes
Timer 2
Seconds
Number of Repeats
ll
llll
l
l
ll
lll
ll
E-28
3. When the setting you want to change is fl ashing, use
D
and
B
to change it as
described below.
Setting
Screen
Button Operation
Minutes, Seconds
Use
D
(+) and
B
(–) to change the setting.
Number of Repeats
Use
D
(+) and
B
(–) to change the setting.
•
To disable either timer, set 00'00" as its countdown start time.
4. Press
A
to exit the setting screen.
E-29
To use the countdown timer
Current repeat count
Preset number of repeats
(Reset)
(Start/Stop)
Current timer time
Current time
Timer 1 or 2
Press
D
while in the Countdown Timer Mode to start the countdown timer.
•
The countdown is performed by alternating between Timer 1 and Timer 2. A short
beep is emitted to signal a changeover from one timer to the other.
•
Press
D
to pause a countdown. Press
D
again to resume.
•
Pressing
B
while a countdown timer is stopped resets it to the start time specifi ed
by you.
•
The watch emits a 5-second beep when the end of the fi nal timer operation
(specifi ed by the number of repeats) is reached.
•
Even if you exit the Countdown Timer Mode, the countdown timer operation
continues and the watch beeps as required.