Operation Guide 3153
3
To record the time paused on the display
While a time is paused on the display (see above), press the
B
button.
•
This will save the paused time in memory and display the ongoing special
stage timing operation.
•
The watch has enough memory to store up to 30 time records. If there are
already 30 records in memory, storing a new measurement time causes the
oldest record to be deleted automatically to make room for the new one.
To reset the timing operation to zero
While a time is paused on the display (see above), hold down the
B
button.
•
This will reset the elapsed time operation to zero.
The watch has enough memory to store up to 30 measurement time records.
If there are already 30 records in memory, storing a new measurement time
causes the oldest record to be deleted automatically to make room for the
new one.
ll
ll
l l
ll
ll
ll
When the remaining target
time is 5 minutes or more
ll
llll
ll
lll
ll
llll
ll
lll
When the remaining target
time is less than 5 minutes
Target time
Target time
To cancel an ongoing elapsed time measurement operation
Hold down the
B
button to reset the elapsed time operation to zero.
To change screen contents during elapsed time measurement
Press the
B
button to display the remaining target time. Note that this
operation is not available if “OFF” is selected for the target time.
Remaining Target Time Alert
The watch will beep and display illumination will flash when the remaining
target time reaches the following points, 5, 3 and 1 minute, and 30, 10, 5, 4,
3, 2, and 1 second before time up, and at time up.
Recall Mode
You can use the Recall Mode to view the following data in watch memory.
•
Times measured in the Rally Mode
•
Total of the measured times currently in memory (TTL)
•
You can use the
D
(forward) and
B
(back) buttons to scroll through
records as shown below. Holding down either button scrolls the records at
high speed.
•
Holding down the
A
button while a record is displayed will show the date
and time that the measurement was taken.
•
To go straight to the total measured time screen, press the
D
and
B
buttons at the same time.
•
How the hour digits are displayed changes (to a format that requires two
screens) when the total measured time is within the range of 100 hours, 00
minutes and 00 seconds, to 2999 hours, 59 minutes 57 seconds. While the
total measured time is displayed in this case, the display will switch
automatically between the two screens at two-second intervals.
Record 30
Record 1
Total measured
time
B
B
B
D
D
D
Record Number
Measured
elapsed time
Measurement date and time
Measured elapsed time
Measurement time
(Hour : Minutes)
Measurement date
(Month – Day)
▲
▲
A
A
Total measured
time
Hour digits screen
Total measured time (TTL)
When the total measured time
is in the range of zero to 2999
hours, 59 minutes 57 seconds
Minute digits screen
Switches automatically
at two-second intervals
▲
▲
Switches automatically
at two-second intervals
To correct recorded times
You can use the procedure below to correct times recorded by the watch so
they match official race times. The total measured time value also is updated
in accordance with the corrected times.
1. Hold down
A
until the display contents start
to flash. This is the setting screen.
2. Use the
D
(+) and
B
(–) buttons to change
the measured 1/10-second digit.
3. Press the
C
button to move the flashing to
the measured seconds.
4. Use the
D
(+) and
B
(–) buttons to change
the measured seconds.
5. Press the
C
button to move the flashing to the measured minutes.
6. Use the
D
(+) and
B
(–) buttons to change the measured minutes.
7. Press the
C
button to move the flashing to the measured hours.
lll
lll
ll
lllll
8. Use the
D
(+) and
B
(–) buttons to change the measured hours.
9. After the time is what you want, press the
A
button to exit the setting
screen.
•
You can change a measured time to a value up to 99 hours, 59 minutes,
59.9 seconds.
•
Holding down the
D
(+) or
B
(–) button will scroll the selected value at
high speed.
•
To reset the data to all zeros, press the
D
and
B
buttons at the same time.
Measured 1/10
second
Measured
seconds
Measured
minutes
Measured
hours
C
C
C
C
To delete all memory records
You can use the following procedure to clear all
of the measurement data records currently stored
in watch memory.
1. Use the
D
and
B
button to display the total
measurement time screen.
2. Hold down
A
until the display contents start
to flash. This is the setting screen.
3. Press the
D
(+) and
B
(–) buttons at the
same time to delete the records.
4. Press the
A
button to exit the setting screen.
ll
ll
ll
ll
ll
l l
l l l l l l l l l l
ll
l
ll
l
ll
ll
ll
ll
ll
l l l
▲
World Time
World Time shows the current time in 48 cities
(29 time zones) around the world.
•
The times kept in the World Time Mode are
synchronized with the time being kept in the
Timekeeping Mode. If you feel that there is an
error in any World Time Mode time, check to
make sure you have the correct city selected
as your Home City. Also check to make sure
that the current time as shown in the
Timekeeping Mode is correct.
•
Select a city code in the World Time Mode to display the current time in any
particular time zone around the globe. See the “UTC Differential/City Code
List” for information about the UTC differential settings that are supported.
•
All of the operations in this section are performed in the World Time Mode,
which you enter by pressing
C
.
City code
Current time in
selected city
