Operation Guide 3023
2
•
Signal reception is normally better at night than during the day.
•
Time calibration signal reception takes from two to five minutes. Take care that you
do not perform any button operations or move the watch during this time.
•
This watch is designed to pick up the time calibration signal transmitted from Fort
Collins, Colorado (USA).
Reception Range
•
At distances further than about 600 miles (1,000 kilometers) from the transmitter,
signal reception may not be possible during certain times of year or times of day.
Radio interferance may also cause problems with reception.
•
Even when the watch is within the reception range of the transmitter, signal
reception is impossible if the signal is blocked by mountains or other geological
formations between the watch and signal source.
Fort Collins
•
Signal reception is affected by weather, atmospheric conditions, and seasonal
changes.
•
See the information under “Signal Receive Troubleshooting” if you experience
problems with time calibration signal reception.
About Auto Receive
When auto receive is turned on, the watch starts to receive the time calibration signal
automatically when the time in the Timekeeping Mode reaches midnight, 1:00 a.m. ,
2:00 a.m., 3:00 a.m., 4:00 a.m., and 5:00 a.m. (calibration times).
When any auto receive is successful, the remaining auto receive operations are not
performed.
Note
•
Auto receive works only while the watch is in the Timekeeping Mode or World Time
Mode. Auto receive is not performed if an auto receive time is reached while an
alarm is sounding, while a countdown timer operation is in progress, or if a setting
screen (a screen with a flashing setting) is on the display.
•
Auto receipt of the calibration signal is designed to be performed early in the
morning, while you sleep (provided that the Timekeeping Mode time is set correctly).
Before going to bed for the night, remove the watch from your wrist, and put it in a
location where it can receive the signal easily.
•
When auto receive is turned on, the watch receives the calibration signal for two to
five minutes everyday when the Timekeeping Mode time reaches each of the
calibration times. Do not perform any button operation within five minutes before or
after any one of the calibration times. Doing so can interfere with correct calibration.
•
Remember that reception of the calibration signal depends on the time kept in the
Timekeeping Mode. The receive operation will be performed whenever the display
shows any one of the calibration times, regardless of whether or not the
Timekeeping Mode time is actually the correct time.
•
If more than one auto receive is successful, the watch uses the data from the last
successful receive to adjust settings. When only one reception is successful, the
watch uses the data of the successful reception.
About the Receiving Indicator
The receiving indicator shows the strength of the calibration signal being received. For
best reception, be sure to keep the watch in a location where signal strength is
strongest.
Weak
(Level 0)
Strong
(Level 3)
•
Even in an area where signal strength is strong, it takes about 10 seconds for signal
reception to stabilize enough for the receiving indicator to indicate signal strength.
•
Use the receiving indicator as a guide for checking signal strength and for finding the
best location for the watch during signal receive operations.
•
Following reception of the time calibration signal and calibration of the watch’s time
setting, the Level 3 receiving indicator will remain on the display in all modes. The
Level 3 receiving indicator will not be displayed if signal reception was unsuccessful
or after you adjust the current time setting manually.
Receiving indicator
•
The Level 3 receiving indicator is displayed only when the watch is able to receive
both time and date data successfully. It does not appear when only time data is
received.
•
The Level 3 receiving indicator indicates that at least one of the auto calibration
signal receive operations was successful. Note, however, that the Level 3 receiving
indicator is cleared from the display at midnight each day.
To perform manual receive
1. Place the watch on a stable surface so its top (12
o’clock side) is facing towards a window.
2. In the Timekeeping Mode, hold down
C
for about two
seconds until
RC!
appears on the display.
•
Time calibration signal reception takes from two to five
minutes. Take care that you do not perform any button
operations or move the watch during this time.
•
After signal reception is complete, the display of the
watch changes to the Last Signal screen.
Receiving indicator
Note
•
To interrupt a receive operation and return to the Timekeeping Mode, press
C
.
•
If the receive operation is unsuccessful, the message
ERR
appears on the display
for about one or two minutes. After that, the watch returns to the Timekeeping Mode.
•
You can also change from the Last Signal or
ERR
screen to the normal
timekeeping screen by pressing
C
.
To turn auto receive on and off
1. In the Timekeeping Mode, press
C
to display the Last
Signal screen.
2. Hold down
A
until the current auto receive setting (
ON
or
OFF
) starts to flash. This is the setting screen.
•
Note that the setting screen will not appear if the
currently selected Home City is one that does not
support time calibration reception.
3. Press
C
to toggle auto receive on (
ON
) and off (
OFF
).
4. Press
A
to exit the setting screen.
•
For information about city codes that support signal
receive, see “To set your Home City”.
l l l l
l
l
l
l
ll
ll
ll
l
l
l
l
l l
On/Off status
Last Signal Screen
▲
Press
C
.
Receive time
Month – Day
Hour : Minutes
PM indicator
▲
Receive date
To display the Last Signal screen
In the Timekeeping Mode, press
C
to display the Last Signal screen (indicated by
G
ET
). The Last Signal screen shows the date and time of the last successful time
calibration signal reception.
DST indicator
Seconds
Signal Receive Troubleshooting
Check the following points whenever you experience problems with calibration signal
reception.
Problem
Cannot perform
manual receive.
Auto receive is
turned on, but
the Level 3
receiving
indicator does
not appear on
the display.
Time setting is
incorrect
following signal
reception.
Probable Cause
•
The watch is not in the Timekeeping
Mode.
•
Your current Home City is not one of the
following city codes:
YVR
,
LAX
,
YEA
,
DEN
,
MEX
,
YWG
,
CHI
,
MIA
,
YTO
,
NYC
,
YHZ
, or
YYT
.
•
You changed the time setting manually.
•
The watch was not in the Timekeeping
or World Time Mode, or you performed
some button operation during the auto
receive operation.
•
Even if receive is successful, the Level 3
receiving indicator disappears every day
at midnight.
•
Time data (hour, minutes, seconds) only
was received during the last receive
operation. The Level 3 receiving
indicator appears only when time data
and date data (year, month, day) are
both received.
•
If the time is one hour off, the DST
setting may be incorrect.
•
The Home City code setting is not
correct for the area where you are using
the watch.
What you should do
•
Enter the Timekeeping Mode
and try again.
•
Select
YVR
,
LAX
,
YEA
,
DEN
,
MEX
,
YWG
,
CHI
,
MIA
,
YTO
,
NYC
,
YHZ
, or
YYT
as your
Home City.
•
Perform manual signal receive
or wait until the next auto
signal receive operation is
performed.
•
Check to make sure the
watch is in a location where it
can receive the signal.
•
Change the DST setting to
Auto DST.
•
Select the correct Home City
code.
•
For further information, see “Important!” under “Time Calibration Signal Reception”
and “Radio-controlled Atomic Timekeeping Precautions”.
World Time
The World Time Mode shows you the current time in 48
cities (29 time zones) around the world.
•
If the current time shown for a city is wrong, check your
Home City time settings and make the necessary
changes.
•
All of the operations in this section are performed in the
World Time Mode, which you enter by pressing
B
.
City code
Current time in
selected city
To view the time in another city
While in the World Time Mode, press
C
to scroll eastward through the city codes
(time zones).
•
For full information on city codes, see “City Code Table”.
To toggle a city code time between Standard Time and Daylight Saving Time
1. In the World Time Mode, use
C
to display the city code
(time zone) whose Standard Time/Daylight Saving Time
setting you want to change.
2. Hold down
A
to toggle Daylight Saving Time (
DST
indicator displayed) and Standard Time (
DST
indicator
not displayed).
•
The
DST
indicator will appear whenever you display a
city code for which Daylight Saving Time is turned on.
•
Note that the DST/Standard Time setting affects only the
currently displayed city code. Other city codes are not
affected.
DST indicator
Alarms
The Alarm Mode gives you a choice of four one-time
alarms and one snooze alarm.
Also use the Alarm Mode to turn the Hourly Time Signal
(
SIG
) on and off.
•
There are five alarms numbered
AL1
through
AL4
,
and
SNZ
. You can configure
SNZ
as a snooze alarm
only. Alarms
AL1
through
AL4
can be used as one-
time alarms only.
•
All of the operations in this section are performed in the
Alarm Mode, which you enter by pressing
B
.
Alarm time
(Hour : Minutes)
Alarm number
To set an alarm time
1. In the Alarm Mode, use
C
to scroll through the alarm
screens until the one whose time you want to set is
displayed.
2. After you select an alarm, hold down
A
until the hour
setting of the alarm time starts to flash, which indicates
the setting screen.
•
This operation turns on the alarm automatically.
3. Use
B
to move the flashing between the hour and
minute settings.
AL1
AL2
AL3
SIG
SNZ
AL4