background image

USER’S GUIDE 2733

3

When you want to do this:

Move the hand setting
forward 20 seconds

Perform this button operation:

Press 

D

.

To adjust the analog time

1. In the Timekeeping Mode, press 

C

 six times to enter

the Hand Setting Mode.

2. Hold down 

A

 until the current digital time starts to

flash, which indicates the setting screen.

3. Use 

D

 (+) and 

B

 (–) to adjust the analog setting as

described below.

l l l l l

ll

ll

l

l

ll

ll

l l

Current time

Move the hand setting back
20 seconds
Move the hand setting a short
way forward at high speed

Move the hand setting a
short way back at high speed

Move the hand setting a
long way forward at high
speed

Press 

B

.

Hold down 

D

.

Release 

D

 when the hands reach the setting

you want.

Hold down 

B

.

Release 

B

 when the hands reach the setting

you want.

While holding down 

D

 to move the hands at

high-speed, press 

B

 to lock the high-speed

hand movement.

Press any button when the hands are close to
the setting you want.

Hand movement stops automatically if the hour
hand makes one full (12-hour) revolution.

Move the hand setting a long
way back at high speed

While holding down 

B

 to move the hands at

high-speed, press 

D

 to lock the high-speed

hand movement.

Press any button when the hands are close to
the setting you want.

Hand movement stops automatically if the hour
hand makes one full (12-hour) revolution.

4. Press 

A

 to exit the setting screen.

The minute hand will be adjusted slightly to match the seconds when you exit the
setting screen.

To return to the Timekeeping Mode, press 

C

.

World Time

The World Time shows the current time in 30 cities (29
time zones) around the world.
• If the current time shown for a city is wrong, check your

Home City time settings and make the necessary
changes.

• The watch will perform a signal receive operation even if

it is in the World Time Mode when a calibration time is
reached. If this happens, the World Time Mode time
settings will be adjusted in accordance with the
Timekeeping Mode’s Home City time.

• All of the operations in this section are performed in the

World Time Mode, which you enter by pressing 

C

.

City Code

Current time in the
selected city code

To view the time in another city
While in the World Time Mode, press 

D

 to scroll through the city codes (time zones).

• For full information on city codes, see the “City Code Table.”

To toggle a city code time between Standard Time and Daylight Saving Time

1. In the World Time Mode, use 

D

 to display the city code

(time zone) whose Standard Time/Daylight Saving Time
setting you want to change.

2. Hold down 

A

 to toggle Daylight Saving Time (DST

displayed) and Standard Time (DST not displayed).

Note that you cannot use the World Time Mode to
change the DST setting of the Home City code you
currently have selected in the Timekeeping Mode. See
“Daylight Saving Time (DST)” for information about
turning the Home  City code DST setting on and off.

The DST indicator is on the display whenever you
display a city code for which Daylight Saving Time is
turned on.

DST indicator

Note that the DST/Standard Time setting affects only the
currently displayed city code. Other city codes are not
affected.

Alarms

The Alarm Mode gives you a choice of four one-time
alarms and one snooze alarm. One of the one-time
alarms functions as a “target alarm,” which counts the time
remaining from the current Home City time to the target
alarm time.
Also use the Alarm Mode to turn the Hourly Time Signal
on and off.
• There are five alarms named 

AL1

AL2

AL3

TAL

(target alarm), and 

SNZ

. You can configure 

SNZ

 as a

snooze alarm only. Alarms 

AL1

AL2

AL3

, and

TAL

 can be used as one-time alarms only.

• Alarm settings (and Hourly Time Signal settings) are

available in the Alarm Mode, which you enter by
pressing 

C

.

Alarm time
(Hour : Minutes)

Alarm name

To set an alarm time

1. In the Alarm Mode, use 

D

 to scroll through the alarm

screens until the one whose time you want to set is
displayed.

2. After you select an alarm, hold down 

A

 until the hour

setting of the alarm time starts to flash, which indicates
the setting screen.

This operation automatically turns on the alarm.

3. Use 

C

 to move the flashing in the sequence shown

below to select other settings.

AL1

AL2

AL3

SIG

SNZ

TAL

l l

l l l l l l l

ll

ll

ll

ll

ll

l

Minutes

Hour

4. While the hour or minute setting is flashing, use 

D

 (+) and 

B

 (–) to change it.

5. Press 

A

 to exit the setting screen.

• With the target alarm (

TAL

), the time starts to countdown as soon as you set the

alarm time.

Countdown
(Hours : Minutes)

Target Alarm Screen

2 seconds

Note
• When setting the alarm time using the 12-hour format, take care to set the time

correctly as a.m. (no indicator) or p.m. (P indicator).

Countdown
(Seconds)

Alarm Operation

The alarm tone sounds at the preset time for 10 seconds, regardless of the mode the
watch is in. In the case of the snooze alarm, the alarm operation is performed a total
of seven times, every five minutes, until you turn the alarm off.
The target alarm counts the time remaining from the current Home City time to the
target alarm time.
• Pressing any button stops the alarm tone operation.
• Performing any one of the following operations during a 5-minute interval between

snooze alarms cancels the current snooze alarm operation.

Displaying the Timekeeping Mode setting screen
Displaying the alarm setting screen

To test the alarm
• In the Alarm Mode, hold down 

D

 to sound the alarm.

To select the alarm operation type

1. In the Alarm Mode, use 

D

 to select the screen for the

alarm (

AL1

AL2

AL3

TAL

, or 

SNZ

) whose

alarm type you want to select.

2. Press 

A

 to cycle through the available settings in the

sequence shown below.

The alarm on indicator (ALM) or snooze on indicator
(SNZ) is displayed for each alarm (

AL1

AL2

AL3

,

TAL

SNZ

) for which alarm on is selected.

• The snooze on indicator (SNZ) flashes during the 5-

minute interval between alarms.

• The alarm on indicator (ALM) and snooze on indicator

(SNZ) are displayed in all modes.

• In all modes, the alarm on indicator is shown for any

alarm (

AL1

AL2

AL3

TAL

SNZ

) that is

currently turned on.

Snooze on indicator

Alarm on indicator

Alarm/

Snooze on

Alarm/

Snooze off

To turn the Hourly Time Signal on and off

1. In the Alarm Mode, use 

D

 to select the Hourly Time

Signal (

SIG

).

2. Press 

A

 to toggle it on (SIG displayed) and off (SIG

not displayed).

• The Hourly Time Signal on indicator (SIG) is displayed

in all modes when the Hourly Time Signal is turned on.

Hourly time signal
on indicator

Date Alert

Date Alert helps you to remember an important date. After you set an alert date
(month and day), a date alert indicator (!) and the current date flash for 24 hours after
the alert date arrives in the Timekeeping Mode. You can set up to five different date
alerts.

Alert date
(Month–Day)

Alert name

Current date
(Month–Day)

Date alert on
indicator

Date Alert Mode Screen

Timekeeping Mode Screen

l l l l l

ll

l

l

l

l

ll

ll

l l

Содержание 2733






Отзывы: