2273-5
To measure times with the stopwatch
Elapsed Time
Split Time
Two Finishes
*
Pressing
A
here normally clears the stopwatch to all zeros. In the case of
a stopwatch operation started automatically by repeat timing when the end
of a countdown is reached, however, pressing
A
here displays the start
time instead of clearing the stopwatch to all zeros.
STOPWATCH
Using the Stopwatch Mode
The following procedure describes how to enter the Stopwatch Mode from the
countdown timer.
To enter the Stopwatch Mode
1. Press
D
to enter the Countdown Timer/Stopwatch Mode.
2. Hold down
A
until the time setting starts to flash, which indicates the
setting screen.
•
This causes the
indicator to appear on the display.
3. Use
E
(+) and
B
(–) to change the displayed countdown start time to
0'00".
•
Note that you cannot enter the Stopwatch Mode while the countdown
timer start time is any other value besides 0'00".
4. After making the setting you want, press
A
to exit the setting screen.
•
This causes the
indicator to appear on the display, indicating
the Stopwatch Mode.
•
The stopwatch lets you measure elapsed
time, split times, and two finishes.
•
The display range of the stopwatch is 99
hours 59 minutes 59 seconds.
•
The stopwatch measurement operation
continues to run, restarting from zero after it
reaches its limit, until you stop it.
•
The stopwatch measurement operation
continues even if you exit the Stopwatch
Mode.
Minutes
Hours
Seconds
Start
Stop
Re-start
Stop
Clear
Split release
Start
Split
Stop
Clear
Start
Split
First runner
finishes.
Display time
of first
runner.
Stop
Second runner finishes.
Split release
Display time of
second runner.
Clear
E
E
E
E
A
*
E
A
A
E
A
*
E
A
E
A
A
*
•
See “Moon Phase Indicator” for information about the Moon phase
indicator and “Tide Graph” for information about the tide graph.
To view the Moon age for a particular date
1. In the Moon/Tide Mode, press
C
to display the Moon Age Screen.
2. Use
E
(+) and
B
(–) to change the date.
•
You can select a date in the range of January 1, 2000 to December 31,
2039.
•
About one second after you display a date, its Moon age and Moon
phase will appear on the display.
To view tide data for a particular time
1. Use the steps under “To view the Moon
age for a particular date” to specify the
date whose data you want to view.
2. Press
C
to display the Tide Data Screen.
3. Use
E
(+) and
B
(–) to specify the time
whose tide data you want to view.
•
You can change the time in one-hour
increments.
•
When setting the tide data time using the
12-hour format, take care to set the time
correctly as a.m. (no indicator) or p.m. (
P
indicator).
•
The area of the tide graph that
corresponds to the specified date and
time flashes.
About one
second
later
▲
Date (Year Month – Day)
Moon phase
indicator
Tide data time
Moon age
MOON/TIDE MODE
You can use the Moon/Tide Mode to view the Moon age for the current date
and the Moon age, Moon phase, and tidal movements for a particular date.
Important!
Especially when you plan to view the Moon age or tide graph, be sure to
specify the city data as well as the current time/date.
To display Moon and tide data
1. Press
D
to enter the Moon/Tide Mode.
•
The initial date and Moon age are those based on the time, date, and
city code you have set in the Timekeeping Mode.
2. Press
C
to toggle between the Moon Age Screen and the Tide Data
Screen.
•
The initial time setting when you display the Tide Data Screen from the
Moon Age Screen is always 6:00 (AM).
•
The Tide Data Screen shows the Moon phase for the current date, with
the area of the tide graph that corresponds to the specified date and
time flashing.
Press
C
.
▲
Moon Age Screen
Tide Data Screen
Tide data time
Moon phase indicator
Moon
Age
Date (Year Month – Day)
Tide Graph
▲
ALARM
You can set five independent Daily Alarms.
When an alarm is turned on, the alarm tone
sounds when the alarm time is reached. You
can also turn on an Hourly Time Signal that
causes the watch to beep twice every hour on
the hour.
•
The alarm number (
1
through
5
) indicates
an alarm screen.
appears in place of
when the Hourly Time Signal screen
is shown.
•
All of the operations in this section are
performed in the Alarm Mode, which you
enter by pressing
D
.
To set an alarm time
1. In the Alarm Mode, use
E
and
B
to
select the alarm whose time you want to
set.
2. Hold down
A
until the hour digits of the alarm time start to flash, which
indicates the setting screen.
•
This automatically turns on the alarm.
3. Press
D
to move the flashing between the hour and minutes.
4. While a setting is flashing, use
E
(+) and
B
(–) to change it.
•
When setting the alarm time using the 12-hour format, take care to set
the time correctly as a.m. (no indicator) or p.m. (
P
indicator).
5. Press
A
to exit the setting screen.
Alarm Operation
The alarm sounds at the preset time for about 20 seconds (in all modes), or
until you stop it by pressing any button.
To test the alarm
In the Alarm Mode, hold down
C
to sound the alarm.
Alarm Time (Hour : Minutes)
Alarm on indicator
Timekeeping Mode time
Alarm number
AL-1
SIG
AL-2
AL-5
AL-3
AL-4
Press
E
.
Press
B
.