cashco POSR-2 Скачать руководство пользователя страница 15

IOM-POSR-2

15

SECTION IX

NEW REPLACEMENT UNIT:

Contact your local Cashco, Inc., Sales Rep re sen ta-

 tive with the Serial Number and Product code.  With 

this information they can provide a quotation for a 

new unit including a complete description, price and 

availability.

7

IX. ORDERING INFORMATION
 

 

NEW REPLACEMENT UNIT vs PARTS  "KIT" FOR FIELD REPAIR 

To obtain a quotation or place an order, please retrieve the Serial Number and Product Code that was stamped 
on the metal name plate and attached to the unit.  This information can also be found on the Bill of Material 
("BOM"). a parts list that was provided when unit was originally shipped.  (Serial Number typically 6 digits).  
Product Code typical format as follows:  (last digit is alpha character that reflects revision level for the product).

PARTS "KIT" for FIELD REPAIR:

Contact your local Cashco, Inc., Sales Rep re sen ta tive 
with the Serial Number and Product code.  Identify the 
parts and the quantity required to repair the unit from 
the "BOM" sheet that was provided when unit was 
originally shipped. 

NOTE:

 

  Those part numbers that have a quantity indicated un-

der  "Spare Parts" in column "A” re

fl

 ect minimum parts 

required for inspection and rebuild, - "Soft Goods Kit".  
Those in column “B” include minimum trim replace-
ment parts needed plus those "Soft Goods" parts from 
column "A".

If the "BOM" is not available, refer to the cross-sectional 
drawings included in this manual for part identi

fi

 cation 

and selection.

A Local Sales Representative will provide quotation for 
appropriate Kit Number, Price and Availability.

          CAUTION

Do not attempt to alter the original construction of any 
unit without assistance and approval from the factory.  
All purposed changes will require a new name plate 
with appropriate ratings and new product code to 
accommodate the recommended part(s) changes.

The contents of this publication are presented for informational purposes only, and while every effort has been made to ensure their accuracy, they are not to be 

construed as warranties or guarantees, express or implied, regarding the products or services described herein or their use or applicability.  We reserve the right to 

modify or improve the designs or specifications of such product at any time without notice.

Cashco, Inc. does not assume responsibility for the selection, use or maintenance of any product.  Responsibility for proper selection, use and maintenance of any 

Cashco, Inc. product remains solely with the purchaser.

Содержание POSR-2





















Отзывы: