Case CX800 Tier 3 Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 51

background image

1001-3

Lep 7-27691NA

Issued 02-06

GENERAL INFORMATION

Cleanning

Clean all metal parts except bearings, in a suitable
cleaning solvent or by steam cleaning. Do not use
caustic soda for steam cleaning. After cleaning, dry
and put oil on all parts. Clean oil passages with
compressed air. Clean bearings in a suitable cleaning
solvent, dry the bearings completely and put oil on
the bearings.

Inspection

Check all parts when the parts are disassembled.
Replace all parts that have wear or damage. Small
scoring or grooves can be removed with a hone or
crocus cloth. Complete a visual inspection for
indications of wear, pitting and the replacement of
parts necessary to prevent early failures.

Bearings

Check bearings for easy action. If bearings have a
loose fit or rough action replace the bearing. Wash
bearings with a suitable cleaning solvent and permit
to air dry. DO NOT DRY BEARINGS WITH
COMPRESSED AIR.

Needle bearings

Before you press needle bearings in a bore always
remove any metal protrusions in the bore or edge of
the bore. Before you press bearings into position put
petroleum jelly on the inside and outside diameter of
the bearings.

Gears

Check all gears for wear and damage. Replace gears
that have wear or damage.

Oil seals, O-rings and gaskets

Always install new oil seals, O-rings and gaskets. Put
petroleum jelly on seals and O-rings.

Shafts

Check all shafts that have wear or damage. Check
the bearing and oil seal surfaces of the shafts for
damage.

Service parts

Always install genuine Case service parts. When
ordering refer to the Parts Catalog for the correct part
number of the genuine Case replacement items.
Failures due to the use of other than genuine Case
replacement parts are not covered by warranty.

Lubrication

Only use the oils and lubricants specified in the
Operator’s or Service Manuals. Failures due to the
use of non-specified oils and lubricants are not
covered by warranty.

Find manuals at https://best-manuals.com

«
...
6
7
8
9
10
...
»

Содержание CX800 Tier 3




















































Отзывы:

Нет отзывов

Похожие инструкции для CX800 Tier 3

Бренд: Wacker Neuson Страницы: 228

Бренд: Wacker Neuson Страницы: 248

Бренд: Wacker Neuson Страницы: 200

Бренд: LOFTNESS Страницы: 62

Бренд: Wacker Neuson Страницы: 292

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды