background image

INTRODUCTION

Basic instructions - Shop and assembly

Shimming

For each adjustment operation, select adjusting shims and measure the adjusting shims individually using a microm-
eter, then add up the recorded values. Do not rely on measuring the entire shimming set, which may be incorrect, or
the rated value shown on each shim.

Rotating shaft seals

For correct rotating shaft seal installation, proceed as follows:

1. Before assembly, allow the seal to soak in the oil it will be sealing for at least thirty minutes.

2. Thoroughly clean the shaft and check that the working surface on the shaft is not damaged.

3. Position the sealing lip facing the fluid.

NOTE:

With hydrodynamic lips, take into consideration the shaft rotation direction and position the grooves so that

they will move the fluid towards the inner side of the seal.

4. Coat the sealing lip with a thin layer of lubricant (use oil rather than grease). Fill the gap between the sealing lip

and the dust lip on double lip seals with grease.

5. Insert the seal in its seat and press down using a flat punch or seal installation tool. Do not tap the seal with a

hammer or mallet.

6. While you insert the seal, check that the seal is perpendicular to the seat. When the seal settles, make sure that

the seal makes contact with the thrust element, if required.

7. To prevent damage to the seal lip on the shaft, position a protective guard during installation operations.

O-ring seals

Lubricate the O-ring seals before you insert them in the seats. This will prevent the O-ring seals from overturning and
twisting, which would jeopardize sealing efficiency.

Sealing compounds

Apply a sealing compound on the mating surfaces when specified by the procedure. Before you apply the sealing
compound, prepare the surfaces as directed by the product container.

Spare parts

Only use CNH Original Parts or CASE CONSTRUCTION Original Parts.

Only genuine spare parts guarantee the same quality, duration, and safety as original parts, as they are the same
parts that are assembled during standard production. Only CNH Original Parts or CASE CONSTRUCTION Original
Parts can offer this guarantee.

When ordering spare parts, always provide the following information:

• Machine model (commercial name) and Product Identification Number (PIN)

• Part number of the ordered part, which can be found in the parts catalog

51452136 23/07/2018

13

Содержание CX60C























Отзывы: