Case 570NXT Скачать руководство пользователя страница 40 | Manualshive

Страница: 40 / 51

background image

INTRODUCTION

Diesel fuel

Use No. 2 diesel fuel in the engine of this machine. The
use of other fuels can cause the loss of engine power and
high fuel consumption.

In very cold temperatures, a mixture of No. 1 and No. 2
diesel fuels is temporarily permitted.

NOTICE:

See your fuel dealer for winter fuel requirements

in your area. If the temperature of the fuel is below the
cloud point (wax appearance point), wax crystals in the
fuel will cause the engine to lose power or not start.

The diesel fuel used in this machine must meet the specifi-
cations in the chart or Specification D975-81 of the Amer-
ican Society for Testing and Materials.

Specifications for acceptable No. 2 Diesel Fuel

API gravity (minimum)

34

Flash point (minimum)

60 °C

(

140 °F

)

* Cloud point (maximum)

-20 °C

(

-4 °F

)

* Pour point (maximum)

-26 °C

(

-15 °F

)

Viscosity (at)

88 °C

(

190 °F

)

Centistokes

(2.0)

to

(4.3)

Saybolt Seconds Universal

(32)

to

(40)

* Refer to the Notice on this page.

Fuel Storage

If you keep fuel in storage for a period of time, you can get
foreign material or water in the fuel storage tank. Many
engine problems are caused by water in the fuel.

Keep the fuel storage tank outside and keep the fuel as
cool as possible. Remove water from the storage con-
tainer at regular periods of time.

47441594 27/09/2012

36

«
...
38
39
40
41
42
...
»

Содержание 570NXT




















































Отзывы:

Нет отзывов

Похожие инструкции для 570NXT

Бренд: TEXIO Страницы: 167

Бренд: jcb Страницы: 2

Бренд: ITech Страницы: 54

Бренд: Terex Страницы: 87

Бренд: Terex Страницы: 114

BOXER 427 Operators

Бренд: Compact Power Страницы: 86

Бренд: Big Joe Страницы: 124

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды