Case IH AXIAL-FLOW 5130 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 25

Case IH AXIAL-FLOW 5130 Скачать руководство пользователя страница 13

INTRODUCTION

Safety rules Ecology and the Environment

AXIAL-FLOW 5130, AXIAL-FLOW 6130, AXIAL-FLOW 7130

Soil, air, and water are vital factors of agriculture and life in general. When legislation does not yet rule the treatment

of some of the substances which are required by advanced technology, common sense should govern the use and

disposal of products of a chemical and petrochemical nature.

NOTICE:

The following are recommendations which may be of assistance:

• Become acquainted with and ensure that you understand the relative legislation applicable to your country.
• Where no legislation exists, obtain information from suppliers of oils, lters, batteries, fuels, antifreeze, cleaning

agents, etc., with regard to their effect on man and nature and how to safely store, use and dispose of these sub-

stances.

• Agricultural consultants will, in many cases, be able to help you as well.

HELPFUL HINTS

• Avoid lling tanks using cans or inappropriate pressurized fuel delivery systems which may cause considerable

spillage.

• In general, avoid skin contact with all fuels, oils, acids, solvents, etc. Most of them contain substances which may

be harmful to your health.

• Modern oils contain additives. Do not burn contaminated fuels and or waste oils in ordinary heating systems.
• Avoid spillage when draining off used engine coolant mixtures, engine, gearbox and hydraulic oils, brake uids, etc.

Do not mix drained brake uids or fuels with lubricants. Store them safely until they can be disposed of in a proper

way to comply with local legislation and available resources.

• Modern coolant mixtures, i.e. antifreeze and other additives, should be replaced every two years. They should not

be allowed to get into the soil but should be collected and disposed of properly.

• Do not open the air-conditioning system yourself. It contains gases which should not be released into the atmos-

phere. Your CASE IH AGRICULTURE dealer or air conditioning specialist has a special extractor for this purpose

and will have to recharge the system properly.

• Repair any leaks or defects in the engine cooling or hydraulic system immediately.
• Do not increase the pressure in a pressurized circuit as this may lead to a component failure.
• Protect hoses during welding as penetrating weld splatter may burn a hole or weaken them, allowing the loss of

oils, coolant, etc.

47506838 04/04/2013

6

«
...
11
12
13
14
15
...
»

Содержание AXIAL-FLOW 5130


























Отзывы:

Нет отзывов