manualshive.com logo in svg

Cascade REVEX, Инструкция по эксплуатации

Поделиться
Скачать
Cascade REVEX Скачать руководство пользователя страница 12

 

REVO C/REVEX Service Panel Engineering Manual V1.0     Page 12 

 

2. CONFIGURING THE REVO C/REVEX 
COMMUNICATION PORT SETTINGS 

To configure the REVO C/REVEX communication port (i.e. set to correct Modbus 
address 1, 2, 3 or 4 and 19200bps N81) you must make use of the thyristor configurator 
tool that you can download from the CD automation website. 

https://www.cdautomation.com/product/software/#gref

 

 
Here you can also download the drivers for the USB interface 
 
For the service touchscreen, you need to adjust the Modbus slave port on each REVO 
C/REVEX to a Modbus address 1, 2, 3 or 4 and 19200bps N81. 
 
First connect the 24VDC power supply to the Revo C or REVEX unit (see manual) and 
make sure you have connection with it via a micro-usb cable (maybe your mobile phone 
has it). 
 
First check in windows on which comport the interface to the Revo C/REVEX has been 
mapped. Keep on using always the same USB port because windows mappes other 
COMport number to each differen

t USB port (don’t know why?). 

 
Start the thyristor configuration tool and adjust the comport settings to what you found in 
the device settings. Do this with setting-communication 

 

Содержание REVEX



















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды