Cascade 14J Скачать руководство пользователя

Страница: 11 / 24

6871082-R2

INSTALLATION

CL6226.eps

CC0040.eps

WARNING

: Before removing hydraulic

lines or components, relieve pressure

in the hydraulic system. Turn the truck

off and open the truck auxiliary control

valves several times in both directions.

CLAMP

Relief

Cartridge

SIDESHIFT

Supply

Adjust Relief Cartridges

The valve is equipped with relief valve cartridges in both

the SIDESHIFT and CLAMP circuits. Adjustment of these

reliefs is recommended to optimize clamp performance.

NOTE:

External Sideshift function has no relief adjustment.

CLAMP Relief Adjustment – Pressure Gauge Method

The CLAMP relief cartridge is set at the factory per the

pressure specified on the label on the back of the valve.
The CLAMP relief cartridge is set at the factory with a

system back pressure of 350 psi (24 bar). Actual back

pressure with the attachment connected to the truck will

vary. It is recommended to verify the CLAMP pressure as

an initial starting point.

Confirm that

TRUCK

pressure delivered to the

attachment valve is within the range shown on the

attachment nameplate.

Install a 5000 psi (345 bar) pressure gauge (with a No.

4 O-ring fitting) to the valve gauge 'G' port.

From fully open, close the arms at normal speed

to clamp a rigid load, clamp force indicator or fully

bottom cylinders. Release truck handle and read

pressure gauge. Compare gauge pressure with valve

label pressure.

Adjust the

CLAMP

relief cartridge to correct pressure.

Open arms to release clamp pressure. Turn clockwise

(CW) to increase pressure, counterclockwise (CCW) to

decrease pressure.

Repeat steps

and

to confirm setting. Tighten jam

nut.

NOTE:

When adjusting a CLAMP equipped with a three

position regulator valve, Volumetric Force Control (VFC)

or Hydraulic Force Control (HFC), the CLAMP relief must

be adjusted to maximum pressure. Refer to step D to

increase pressure. Adjust the cartridge to the maximum

position.

NOTE:

Adjustment of CLAMP relief pressure according

to load requirements for secure handling and damage

reduction is recommended. Adjust the relief cartridge per

step

–

to obtain a desired pressure setting. Pressure

is not to exceed the maximum pressure setting on the

attachment nameplate. If multiple pressure settings are

desired, contact Cascade for options.

EXTERNAL

SIDESHIFT VALVE

RH CLAMP Ports

LH CLAMP Ports

Increase

Pressure

(CW)

Decrease

Pressure

(CCW)

CLAMP

Relief

Cartridge

CLAMP

Relief

Cartridge

CLAMP

Supply

SIDESHIFT

Supply

CLAMP

Supply

CLAMP

Supply

Содержание 14J

























Результаты поиска

Содержание 14J

Отзывы:

Похожие инструкции для 14J

Бренды по названию

Популярные бренды

Cascade 14J, Инструкции по установке и периодическому техническому обслуживанию

Результаты поиска

Содержание 14J

Отзывы:

Похожие инструкции для 14J

Бренды по названию

Популярные бренды