Casablanca C3443001 AT0209 Скачать руководство пользователя страница 5

5

V

ermont

®

C

ircuit Breaker

(Trip breaker for the

circuit you will be

working on)

Fuse Box

(Remove fuse for the

circuit you will be

working on)

18"  

84"  

70" 

Safe USe

IntrodUctIon

Before YoU Start

from bottom 
edge of blade 

to floor

from wall 
to end of 
blade

from wall to 
center of fan

dimensions indicated are the minimum 
allowable for proper installation.

 

CAuTIon: RISK oF ElECTRICAl SHoCK!  Installation is to be in accordance with the national Electrical Code, 

AnSI/nFPA 70-1999, and local codes. If you are unfamiliar with the wiring codes, you should use a qualified 

electrician.  To avoid overheating and possible damage to other equipment, do not install control to a receptacle, 

fluorescent light fixture, motor-operated appliance, or transformer-supplied appliance.

•  This fan is designed to be installed on an existing electrical outlet box. The outlet box must be Ul listed for 

ceiling fan installations. If it is not, a new box must be installed. 

• 

This ceiling fan requires a grounded electrical supply of 120 VAC, 60 Hz and a minimum 15 amp circuit. The 

maximum current requirement for the fan with light fixture is 2.17 amps. The fan uses about .71 amp or 85 watts. 

Maximum light current is about .83 amps or 100 watts of lighting.

  Where wire nuts are employed, be sure all bare wires are within the connectors. 

  WARnInG: do not bend the blade brackets when installing the brackets, balancing the blades, or cleaning the 

fan. do not insert foreign objects in between the rotating fan blades.

Unpacking

Before  assembling  and  installing  your  ceiling  fan,  remove  all  parts  from  the  shipping  cartons  and  check  them 
against the parts listed in the Parts Guide. Before discarding packaging materials, be certain that all parts have 
been removed.

For best performance and for your warranty to be valid,  

use only genuine Casablanca blades, light fixtures, and accessories.

  The blades in each pack are matched for equal weight 

to assure smooth fan operation. If more than one fan 
is being installed, be careful not to mix blades from 
different cartons.

  Inspect  the  contents  of  your  carton  for  possible 

shipping or handling damage. If parts are missing or 
damaged, call 1-888-227-2178.

  It is always a good idea to have an assistant to help 

with the installation.

  When cleaning, painting, or working near your fan, 

be very careful of the fan and blades. Always turn the 
power oFF to the ceiling fan before working on it or 
replacing lightbulbs. 

  never insert anything into the path of the fan blades 

while the fan is in operation.

•  never install a fan over a pool or spa. 

  never  operate  a  fan  that  has  been  damaged 

i n   a n y   w a y.   F o r   a s s i s t a n c e   i n   o b t a i n i n g 
service,  call  Casablanca  Fan  Company  at  
1-888-227-2178  or  contact  your  local  authorized 
Casablanca dealer.

Содержание C3443001 AT0209






















Отзывы: