SAFETY INSTRUCTIONS (EUROPEAN)
The conductors in the AC power cord are colored in accordance with the following code.
GREEN & YELLOW—Earth BLUE—Neutral BROWN—Live
U.K. MAIN PLUG WARNING: A molded main plug that has been cut off from the cord is
unsafe. NEVER UNDER ANY CIRCUMSTANCES SHOULD YOU INSERT A DAM-
AGED OR CUT MAIN PLUG INTO A POWER SOCKET.
IMPORTANT! FOR YOUR PROTECTION, PLEASE READ THE FOLLOWING:
WATER AND MOISTURE: Appliance should not be used near water (near a bathtub, washbowl,
kitchen sink, laundry tub, in a wet basement, or near a swimming pool, etc). Care should be taken
so that objects do not fall and liquids are not spilled into the enclosure through openings.
POWER SOURCES: The appliance should be connected to a power supply only of the type
described in the operating instructions or as marked on the appliance.
GROUNDING OR POLARIZATION: Precautions should be taken so that the grounding or polar-
ization means of an appliance is not defeated.
POWER CORD PROTECTION: Power supply cords should be routed so that they are not likely to
be walked on or pinched by items placed upon or against them, paying particular attention to
cords at plugs, convenience receptacles, and the point where they exit from the appliance.
SERVICING: The user should not attempt to service the appliance beyond that described in the
operating instructions. All other servicing should be referred to qualified service personnel.
FUSING: If your unit is equipped with a fuse receptacle, replace only with the same type fuse.
Refer to replacement text on the unit for correct fuse type.
REFER SERVICING TO QUALIFIED SER-
VICE PERSONNEL! THIS UNIT CON-
TAINS HIGH VOLTAGE INSIDE!
CAUTION
RISK OF ELECTRIC SHOCK
This symbol is intended to alert the user to the
presence of uninsulated “dangerous voltage”
within the product’s enclosure that may be of
sufficient magnitude to constitute a risk of
electric shock to persons.
LIMITED WARRANTY
Your Carvin amplifier is guaranteed against failure for ONE YEAR unless otherwise stated. Carvin
will service and supply all parts at no charge to the customer providing the unit is under warranty.
Shipping costs are the responsibility of the customer. CARVIN DOES NOT PAY FOR PARTS OR SER-
VICING OTHER THAN OUR OWN. A COPY OF THE ORIGINAL INVOICE IS REQUIRED TO VERIFY
YOUR WARRANTY. Carvin assumes no responsibility for horn drivers or speakers damaged by this
unit. This warranty does not cover, and no liability is assumed, for damage due to: natural disasters,
accidents, abuse, loss of parts, lack of reasonable care, incorrect use, or failure to follow instructions.
This warranty is in lieu of all other warranties, expressed or implied. No representative or person is
authorized to represent or assume for Carvin any liability in connection with the sale or servicing of
Carvin products. CARVIN SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES.
When RETURNING merchandise to the factory, you may call
800-854-2235
for a return authoriza-
tion number. Describe in writing each problem. If your unit is out of warranty, you will be charged
the current FLAT RATE for parts and labor to bring your unit up to factory specifications.
HELP SECTION
1) AMP WILL NOT TURN ON
Check the power to the amp. Check for tripped circuit breakers, unplugged extension cords or
power-strip switches that may be turned off.
2) SX200/H AMP SHUTS OFF WHILE PLAYING
Check the rear SPK IPM switch to make sure it is set properly. Switch to the 4
Ω
position if you
are unsure where to set it. If the problem continues, contact our service technicians.
3) NO OUTPUT with POWER LIGHT ON
Make sure that your speaker is functioning and not blown. Check input, cables & effects
connected to the effects loop, and extension speaker cables for defects & connections.
a) Also verify the effects loop is working by inserting a 1/4” stereo plug into the return jack and
short the tip and ring. If the amp works by doing this, the effects loop jack is defective.
4) KEEP YOUR AMP LOOKING NEW
Try to keep your amplifier free from dust and moisture. To clean, use a damp cloth to wipe the con-
trols chassis panel and wipe the vinyl covering. Use a dry cloth to be sure the moisture is removed.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
SX300C COMBO 2x12” & SX300H
COMPONENT
QTY/BILL U/M DESCRIPTION
SX300R:
03-00560 7 EACH
STANDOFF W/ANTI SPIN .56X.25"
03-63294 1 EACH
STANDOFF ALUM 6-32x .25x .94
05-01603 1 EACH
PWR AC 3/16AWG 8' 2" W/PLUGS
05-62420 1 EACH
CABLE RIBBON 24A 2P/ 8" W/HDR
05-64430 1 EACH
CABLE RIBBON 24A 4P/12" W/HDR
05-68430 2 EACH
CABLE RIBBON 24A 8P/12" W/HDR
06-10001 7 EACH
PPH #4 X .875 TYPE AB BLACK
06-10045 6 EACH
SMS PFH #6X .375 TYPE AB BLACK
06-10051 4 EACH
MS PFH 6-32X .250 BLACK
06-10061 1 EACH
SMS PPH #6 X .375 TYPE A BLACK
06-10133 2 EACH
SMS PPH (#8x.375) TYPE A BLK.
06-50030 4 EACH
NUT KEP #6-32 BLACK OXIDE
06-50035 1 EACH
NUT KEP #6-32 ZINC CADMIUM
07-01603 12 EACH
KNOB "6L" 6x6x17.4mm GREY CAP
07-00105B 16 EACH
KNOB SX BLACK W/WHITE NUMBERS
07-00106 1 EACH
KNOB SX BLACK W/WHITE
10-03301B 1 EACH
FRONT PANEL SX300R
10-30005 1 EACH
PANEL COVER TOPSIDE EQ/XC/XP
10-30014E 1 EACH
CHASSIS UNIVERSAL ONE SPACE
77-03301B 1 EACH
LABEL FRONT SX300R
77-03303B 1 EACH
LABEL S/N OUTPUT JACKS SX300R
80-03301 1 EACH
PCB ASSY MAIN SX300C RACK SMT PCB REV.
SX300C COMBO 2x12” & SX300H
COMPONENT
QTY/BILL U/M DESCRIPTION
03-01200 1 EACH STRAIN RELIEF .625 CHS/.35 CBL
03-18190 1 EACH CABLE TIE 4”LX .10”W 7/8 BNDLE
03-21800A 2 EACH MICA INSULATOR TO-218 0.002”
03-44319 1 EACH WASHER NYLON .157IDx.315Dx.197
03-49553 2 EACH TAPE W/ADHSVE 3M .375 X .375
03-52221 1 EACH GROMMET RUBBER .375” DIAMETER
03-60043 1 EACH SIL PAD W/ADHESIVE 9 MIL
03-77704 1 EACH LENS METAL RED THREADED
03-80602 4 EACH GROMMET NAT PLASTI SCRW #8/10
05-00111 1 EACH CABLE SPKR 24” 16AWG QUICK CON
05-00120 1 EACH CABLE SPEAKER JUMPER 150MM
05-01605 1 EACH PWR AC 16AWG SJT 8’ W/125MM ST
05-46020 1 EACH SPADE CONNECT 16AWG BLK 203MM
05-48025 1 EACH SPADE CONNECT 18AWG BLK 254MM
05-64410 1 EACH CABLE RIBBON 24A 4P/ 4” W/HDR
05-64435 1 EACH CABLE RIBBON 24A 4P/ 14” W/HDR
05-68415 1 EACH CABLE RIBBON 24A 4P/ 6” W/HDR
05-68430 1 EACH CABLE RIBBON 24A 8P/12” W/HDR
05-96545 1 EACH SPADE CONNECT 16AWG GRN/YEL 5”
06-09252 15 EACH NUT FOR POT 71-09252C
06-10070 8 EACH MS PPH 6-32X .500 BLACK
06-10133 2 EACH SMS PPH (#8x.375) TYPE A BLK.
06-10174 4 EACH SMS POH #10X 1.25 TYPE A BLACK
06-11120 1 EACH NUT METRIC 12MM KUNMING BLACK
06-11905 6 EACH NUT METRIC 9MM CHROME SHIMWOO
06-11906 6 EACH WSH METRIC 9MM CHROME SHIMWOO
06-30035 4 EACH WSH FLANGED #10 BLACK OXIDE
06-40070 1 EACH TERMINAL .25”TAB/.156”LUG/.032
06-50030 8 EACH NUT KEP #6-32 BLACK OXIDE
06-50053 4 EACH NUT RETAINER U-TYPE #10 SCREW
07-00105B 16 EACH KNOB SX BLACK W/WHITE NUMBERS
07-00106 1 EACH KNOB SX FEATURE BLACK W/WHITE
10-03201D1 EACH CHASSIS SX-AMP 100W 3-CHANNEL
10-03202C 1 EACH COMBO HEAD
25-31350 1 EACH SWITCH DPST ROCKER BLACK POWER
76-00001 1 EACH WARRANTY CARD “CARVIN”
77-03300 1 EACH LABEL FRONT SX300C
77-03302 1 EACH LABEL OUTPUT JACKS SX300C
77-03204 1 EACH LABEL SERIAL NUMBER SX AMPS
80-03300 1 EACH PCB ASSY MAIN SX300C SMT PCB
87-20120 1 EACH CABINET ASSY SX300C 2X12 COMBO
87-3200 1 EACH CABINET ASSY. HEAD
REPLACEMENT PARTS LIST
