7
14
9
13
Typical STereo SeTup
(or mono bi-amp)
8
Bridged Mono
12
HelPFUl HINTS
5) dedICATed CIRCUIT BReAkeR: each amp will require
a dedicated circuit breaker for its full output. There will be
a sustained loss of power if the AC voltage falls below the
rated 120V or 230/240V input. Normally a 2000w amp or
higher would require its own 20 amp circuit to deliver its
full power at 2 ohms/channel or 4 ohms bridged.
1) No SoUNd FRoM CH 2: The rear (recessed) BRIdGe
switch has been inadvertently pushed in.
2) STeReo CHANNelS SoUNd THe SAMe: The rear
PARAllel switch has been inadvertently pushed in.
3) No HIGH FReqUeNCIeS: Tweeters or midrange drivers have
been damaged or blown from feedback or to much power.
4) PooR SoUNd (BASS): The speaker systems are wired out
of phase to each other. To correct, check polarity and if nec-
essary reverse the wires on one speaker connector only and
your sound, especially the bass will improve.
10
11
leFT
RIGHT
BiaMping
MUST USE AN ELECTRONiC CROSSOVER OR SPEAKER MANAgEMENT SYSTEM TO SEPARATE HigH AND LOw FREQUENCiES
8 OHM 300W/CH - 900W BRIDGE
4 OHM 450W/CH - 1500W BRIDGE
2 OHM (MIN) 750W/CH
120-240V AC 50/60Hz 1000V A
BRIDGE
OUTPU T
SPEAKONS™
AC C E P T 1/4 INC H J AC K S
INPUT
INPUT
INPUT
PAR ALLE L
100Hz
BRIDGE
1
2
1
2
HD1500
PARALLEL
switch must be OFF (OUT).
Ch 1 Low Frequencies
Ch 2 High Frequencies
BRiDgE switch
must be OFF (OUT).
4-pin Speakon
2-pin
2-pin
Right Full Range
For (stereo) the PARALLEL
switch must be OFF (OUT).
Left (Mono) Full Range
Ch 1 Left
Ch 2 Right
BRiDgE switch
must be OFF (OUT).
8 OHM 300W/CH - 900W BRIDGE
4 OHM 450W/CH - 1500W BRIDGE
2 OHM (MIN) 750W/CH
120-240V AC 50/60Hz 1000V A
BRIDGE
OUTPUT
SPEAKONS™
ACCEPT 1/4 INCH JACKS
INPUT
INPUT
INPUT
PAR ALLE L
100Hz
BRIDGE
1
2
1
2
HD1500
PARALLEL switch OFF (OUT).
8 OHM 300W/CH - 900W BRIDGE
4 OHM 450W/CH - 1500W BRIDGE
2 OHM (MIN) 750W/CH
120-240V AC 50/60Hz 1000V A
BRIDGE
OUTPUT
SPEAKONS™
ACCEPT 1/4 INCH JACKS
INPUT
INPUT
INPUT
PAR ALLE L
100Hz
BRIDGE
1
2
1
2
To signal socket XLR or 1/4" 2 or 3 cond. shielded
Activate the BRiDgE switch
(iN). Control the level by Ch 1
(Ch 2 does not function.)
Ch 1 input
Single speaker or
system connected
in BRiDgE mode.
Minimum imp. 4 w
Use either the
Bridged Speakon™
connector or the
binding posts. No
other connections
can be used while in
Bridged mode.
Connect the DCM1015 in
“bridge mode” to deliver 70
volts. Higher powered amps
will exceed 70v, damaging
transformers and speakers.
+
16
8
4
C
15w
7w
3w
1w
C
+
16
8
4
C
15w
7w
3w
1w
C
HD1500
8 OHM 300W/CH - 900W BRIDGE
4 OHM 450W/CH - 1500W BRIDGE
2 OHM (MIN) 750W/CH
120-240V AC 50/60Hz 1000V A
BRIDGE
OUTPU T
SPEAKONS™
AC C E P T 1/4 INC H J AC K S
INPUT
INPUT
INPUT
PAR ALLE L
100Hz
BRIDGE
1
2
1
2
HD1500
PARALLEL
switch must be OFF (OUT).
Ch 1 Low Frequencies
Ch 2 High Frequencies
BRiDgE switch
must be OFF (OUT).
4-pin Speakon
2-pin
2-pin
Using the internal 100Hz crossover into a single sub bridged,
press the channel one 100Hz switch.