L11
JACK
S5
5 POSITION SWITCH
SIDE VIEW
SWITCH POSITIONS:
1. NECK
2. NECK/MIDDLE
3. MIDDLE
4. MIDDLE/BRIDGE
5. BRIDGE
GND
BLK
BLK
BLK
GROUND WIRE
FROM BRIDGE
RED
RED
ON
OFF
S3
BRIDGE
PICKUP
SWITCH
C1
GND
GND
BLK
BLK
RED
GND
BLK
RED
RED
BRIDGE
PICKUP
NECK PICKUP
MIDDLE PICKUP
P1
VOL
P2
TONE
TWIST-ON
WIRE NUTS
OPTIONAL:
SOLDER DIRECT
TO VOLUME
& TONE
L11
JACK
S5
5 POSITION SWITCH
SIDE VIEW
SWITCH POSITIONS:
1. NECK
2. NECK/MIDDLE
3. MIDDLE
4. MIDDLE/BRIDGE
5. BRIDGE
GND
BLK
BLK
TWIST-ON
WIRE NUTS
OPTIONAL:
SOLDER DIRECT
TO VOLUME
& TONE
BLK
GROUND WIRE
FROM BRIDGE
RED
RED
DUAL
SINGLE
S3
BRIDGE
SWITCH
C1
GN
D
GN
D
BL
K
BL
K
RED
GN
D
WHT
RED
RED
NECK PICKUP
MIDDLE PICKUP
BRIDGE
HUMBUCKING
PICKUP
P1
VOL
P2
TONE
BLK
PICKGUARD
Before you screw down the pickguard you must attach the black col-
ored ground wire from the spring claw on the tremolo model (or) the
black colored ground wire from under the FT6 fixed bridge. Use one
of the 2 supplied wire nuts to attach the black colored ground wire
coming from the jack cavity along with the black colored ground wire
coming from the fixed bridge or tremolo to the 5’ long black colored
ground wire that is soldered to the back of the tone pot. Hold the
ends of these three wires together and twist on the wire nut. Now
take the red hot wire from the jack and connect it with the 5’ long red
wire coming from the center terminal of the volume pot. Hold the
ends of these two wires together and twist on the other wire nut.
The wiring is now done, however, if you prefer you, can eliminate the
wire nuts and solder directly to the potentiometers on the pickguard.
Now slide the upper portion of the pickguard underneath the finger-
board. Make sure that the wires underneath the pickguard fit inside
the routed pockets of the body so that the pickguard fits flush and
flat on the top of the body. After making sure none of the wires are
sandwiched between the pickguard and the top of the body, use the
#1 tip phillips head screw driver to screw down the pickguard with
the eleven #4 x 1/2” wood screws.
Diagram 1.
AG1 assembly
3 single coil pickups
with bridge On/Off switch
which allows you to get the
neck & bridge pickups together
or all 3 pickups at once when
its turned on.
Diagram 2.
AG2 assembly
2 single coil pickups
1 humbucker
Dual/Single coil switch
L11
JACK
S5
5 POSITION SWITCH
SIDE VIEW
SWITCH POSITIONS:
1. NECK
2. NECK/MIDDLE
3. MIDDLE
4. MIDDLE/BRIDGE
5. BRIDGE
GND
BLK
BLK
BLK
GROUND WIRE
FROM BRIDGE
RED
RED
ON
OFF
S3
BRIDGE
PICKUP
SWITCH
C1
GND
GND
BLK
BLK
RED
GND
BLK
RED
RED
BRIDGE
PICKUP
NECK PICKUP
MIDDLE PICKUP
P1
VOL
P2
TONE
TWIST-ON
WIRE NUTS
OPTIONAL:
SOLDER DIRECT
TO VOLUME
& TONE
L11
JACK
S5
5 POSITION SWITCH
SIDE VIEW
SWITCH POSITIONS:
1. NECK
2. NECK/MIDDLE
3. MIDDLE
4. MIDDLE/BRIDGE
5. BRIDGE
GND
BLK
BLK
TWIST-ON
WIRE NUTS
OPTIONAL:
SOLDER DIRECT
TO VOLUME
& TONE
BLK
GROUND WIRE
FROM BRIDGE
RED
RED
DUAL
SINGLE
S3
BRIDGE
SWITCH
C1
GN
D
GN
D
BL
K
BL
K
RED
GN
D
WHT
RED
RED
NECK PICKUP
MIDDLE PICKUP
BRIDGE
HUMBUCKING
PICKUP
P1
VOL
P2
TONE
BLK
