Carrier ZS Скачать руководство пользователя страница 9

Страница: 9 / 49

Creating Snap control programs for ZS Sensors

ZS Sensor

Applications Guide

If a controller supports:

•

Only one control program, you can wire up to 5 ZS sensors to its

Rnet

port.

•

Multiple control programs, you can wire up to 15 ZS sensors to its

Rnet

port. A control program can use no

more than 5 ZS Sensors, so you must use multiple control programs if your Rnet network has more than 5

sensors.

Do the following to create your control program:

Step 1: Add a Sensor Binder microblock.

(page 5)

Step 2: Add Analog Sensed Value Input microblocks.

(page 6)

Step 3: Add Binary Sensed Value Input microblocks.

(page 9)

Step 4: Add a BACnet Setpoint microblock.

(page 11)

Step 5: Add a BACnet Time Clock microblock.

(page 13)

Step 6: Add optional values, status, and icons.

(page 14)

Step 7: Set the order of information displayed on a sensor.

(page 14)

See the Microblock Reference Help for a full description of each of the above microblocks.

Step 1: Add a Sensor Binder microblock

From the Snap

Net I/O

microblock menu, add 1

Sensor Binder

microblock to the workspace to enable

communication between microblocks in the control program and up to 5 ZS Sensors. Enter the following

information in the Property Editor.

Sensor Configuration

The Index number is a reference number for each sensor that you define in

this microblock. ASVI and BSVI microblocks will refer to the sensors by their

index number.

Area

Type an intuitive name for the ZS sensor's location. This name will appear in

the ASVI, BSVI, and Setpoint microblocks in the i-Vu interface.

Network Type

Select Rnet for each ZS Sensor that you define.

Address

The physical address (0–14) set on the ZS sensor's DIP switches.

Lock Display

Check to lock a ZS Pro or ZS Pro-F sensor's buttons. The sensor's Home

screen will display a icon. The lock can be overridden in the i-Vu interface

or at the sensor by a user that knows the override procedure.

Creating Snap control programs for ZS Sensors

Содержание ZS














































Результаты поиска

Содержание ZS

Отзывы:

Бренды по названию

Популярные бренды

Carrier ZS, Инструкция по применению

Результаты поиска

Содержание ZS

Отзывы:

Бренды по названию

Популярные бренды