Carrier WeatherMaker 50TCQA07 Скачать руководство пользователя страница 45 | Manualshive

Страница: 45 / 48

Carrier WeatherMaker 50TCQA07 Скачать руководство пользователя страница 45

45

Step 12 — Install Accessories

Available accessories include:

Roof Curb
Thru--base connection kit (must be installed before unit

is set on curb)
Manual outside air damper
Two--Position motorized outside air damper
EconoMi$er IV (with control and integrated barometric

relief)
EconoMi$er2 (without control/for external signal and

integrated barometric relief)
Power Exhaust
Differential dry--bulb sensor (EconoMi$er IV)
Outdoor enthalpy sensor
Differential enthalpy sensor
Time Guard II compressor anti--cycle control
Outdoor coil hail guard
Outdoor coil protector grille
Head pressure control
Programmable setback thermostat
Electrical/Mechanical thermostat and subbase
Thermidistat

t

device

Humidistat
Electric Heaters
Single Point kits
Thermostat / Sensors
CO

2

sensor

DDC interface (PremierLink)
Louvered hail guard
Phase monitor control

Refer to separate installation instructions for information

on installing these accessories.

Pre--Start and Start--Up

This completes the mechanical installation of the unit.

Refer to the unit’s Service Manual for detailed Pre--Start

and Start--up instructions.

50TC

Q

A

«
...
43
44
45
46
47
...
»

Содержание WeatherMaker 50TCQA07

















































Отзывы:

Нет отзывов