Carrier WeatherMaker 48TC A/B07 Series Скачать руководство пользователя страница 56

Страница: 56 / 60

Fig. 81 —

V-Belt Force Label

BELT TENSION METHOD
Requires belt tension gage that measures tension in belt in units of

lbs force.

Fig. 82 —

Belt Drive Motor Mounting

Pre-Start and Start-Up

This completes the mechanical installation of the unit. Refer to the

unit’s Service Manual for detailed Pre-Start and Start-Up instruc

tions. Download the latest versions from HVAC Partners

(www.hvacpartners.com).

Troubleshooting the Ultra Tech™ Compressor

The Ultra Tech

compressor’s molded plug should be used at all

times. The maximum power is 5A.
MODULATION CONTROL INPUT SPECIFICATIONS
The compressor will modulate from part load to full load when the

voltage supplied to the molded plug is 18 to 28vdc or 18 to 28 vac

rectified to vdc. The compressor will modulate from full load to

part load when the current in the circuit drops below 0.9 MA. See

Table 24 and Fig. 83 for details.

TORQUE ALL SHEAVE SET SCREWS TO 110-130 in. lbs

SET
SCREW

STRAIGHT
EDGE

BELT SPAN

BELT DEFLECTION FORCE - SEE TABLE 1

DEFLECTION = BELT SPAN

Table 1

Table 2

BELT

CROSS

SECTION

SMALLEST

SHEAVE

DIAMETER

BELT DEFLECTION FORCE (LBS)

UNNOTCHED

BELTS

NOTCHED BELTS

USED

NEW

USED

NEW

A, AX

3.0-3.6

3.7

5.5

4.1

6.1

3.8-4.8

4.5

6.8

5.0

7.4

5.0-7.0

5.4

8.0

5.7

8.4

B, BX

3.4-4.2

—

4.9

7.2

4.4-5.6

5.3

7.9

7.1

10.5

5.8-8.6

6.3

9.4

8.5

12.6

BELT CONDITION

TENSION FORCE IN BELT (LBS)

New

100

Used

1. UltraTech™ is a trademark of Emerson Climate Technologies, Inc.

BLOWER PULLEY

V-BELT

MOTOR
PULLEY

MOTOR

MOTOR MOUNTING

PLATE

MOUNTING

BOLTS (4)

Table 24 —

Troubleshooting Ultra Tech Compressor

STAGE

CAPACITY

METERING

LIQUID LINE

SOLENOID

COMPRESSOR

UNLOADER

FOR ULTRA TECH

COMPRESSOR

TROUBLESHOOTING

(COMPRESSOR CURRENT)

FOR LIQUID LINE SOLENOID

VALVE TROUBLESHOOTING

(TOP EVAPORATOR COIL

TEMPERATURE)

Part Load

(66%)

TXV

Closed (De-

energized)

De-energized

Approx. 80% or less

Top section of the evaporator coil

will not be cold (U-bend tubes)

Y1+Y2

Full Load

(100%)

TXV+Fixed Open (Energized)

Energized

100%

Top section of the evaporator coil

will be cold (U-bend tubes)

Содержание WeatherMaker 48TC A/B07 Series





























































Результаты поиска

Содержание WeatherMaker 48TC A/B07 Series

Отзывы:

Бренды по названию

Популярные бренды

Carrier WeatherMaker 48TC A/B07 Series, Руководство по установке

Результаты поиска

Содержание WeatherMaker 48TC A/B07 Series

Отзывы:

Бренды по названию

Популярные бренды