Carrier WeatherMaker 48TC A/B07 Series Скачать руководство пользователя страница 28

Страница: 28 / 60

Fig. 34 —

Thru-Base Connection Fittings

(07 units built on or after 4/15/2019)

The thru-base gas connector has male and female threads. The

male threads protrude above the basepan of the unit; the female

threads protrude below the basepan.

Check tightness of connector lock nuts before connecting gas pip

ing.

Install a

-in. NPT street elbow on the thru-base gas fitting. At

tach a

-in. pipe nipple with minimum length of 16-in. (406 mm)

(field-supplied) to the street elbow and extend it through the ac

cess panel at the gas support bracket. See Fig. 35 and Fig. 36.

Fig. 35 —

Gas Line Piping (Sizes 07-14)

Fig. 36 —

Thru-Base Gas Line Piping for 48TC**07

Units Built On or After 4/15/19

FACTORY-OPTION THRU-BASE GAS CONNECTIONS

(SIZE 16)
This service connection kit consists of a

-in. NPT gas adapter

fitting (stainless steel), a

-in. electrical bulkhead connector and a

-in. electrical bulkhead connector, connected to an “L” bracket

covering the embossed (raised) section of the unit basepan in the

condenser section. See Fig. 37.

1. Remove the “L” bracket assembly from the unit (see

Fig. 37).

2. Cut and discard the wire tie on the gas fitting. Hand-

tighten the fitting if it has loosened in transit.

3. Remove connector plate assembly from the “L” bracket

and discard the “L” bracket, but retain the washer head

screws and the gasket (located between the “L” bracket

and the connector plate assembly

NOTE: Take care not to damage the gasket, as it is reused in the

following step.

4. Place the gasket over the embossed area in the basepan,

aligning the holes in the gasket to the holes in the basepan.

See Fig. 38.

5. Install the connector plate assembly to the basepan using 8

of the washer head screws.

Fig. 37 —

Thru-Base Connection Fittings

(Size 16 Shown)

Fig. 38 —

Completing Installation of Thru-the-Base

Option (Size 16 Shown)

NOTE: If gas and/or electrical connections are not going to occur

at this time, tape or otherwise cover the fittings so that moisture

does not get into the building or conduit in the interim.

LOW VOLTAGE
CONDUIT
CONNECTOR

HIGH VOLTAGE
CONDUIT
CONNECTOR

BRASS FITTING FOR
3 TO 6 TON UNITS

AUXILIARY
POWER
SUPPLY
(OPTIONAL)

EMBOSSMENT

BRASS FITTING
FOR 3-6 TON UNITS

SUPPORT
BRACKET

EMBOSSMENT

BRASS FITTING

FOR GAS PIPING

SUPPORT

BRACKET

” ELECTRICAL

BULKHEAD
CONNECTOR

” ELECTRICAL

BULKHEAD
CONNECTOR

” NPT GAS

ADAPTER
FITTING

“L” BRACKET

GASKET

CONNECTOR
PLATE
ASSEMBLY

Содержание WeatherMaker 48TC A/B07 Series





























































Результаты поиска

Содержание WeatherMaker 48TC A/B07 Series

Отзывы:

Бренды по названию

Популярные бренды

Carrier WeatherMaker 48TC A/B07 Series, Руководство по установке

Результаты поиска

Содержание WeatherMaker 48TC A/B07 Series

Отзывы:

Бренды по названию

Популярные бренды