manualshive.com logo in svg

Carrier WeatherExpert Puron 50JC04, Руководство по установке

Поделиться
Скачать
Carrier WeatherExpert Puron 50JC04 Скачать руководство пользователя страница 2

2

MODEL NUMBER NOMENCLATURE AND 

DIMENSIONS

See Fig. 1 for 50JC model number nomenclature. See Fig. 2 (on

pages 4-6) for unit dimensional drawings and service clearance

dimensions.

Rated Indoor Airflow

Table  1  lists  the  rated  indoor  airflow  used  for  the  AHRI

efficiency rating for the units covered in this document.

Table 1 — 

Rated Indoor Airflow

WARNING

UNIT OPERATION AND SAFETY HAZARD

Failure to follow this warning could cause personal injury,

death and/or equipment damage.

R-410A refrigerant systems operate at higher pressures than

standard R-22 systems. Do not use R-22 service equipment or

components on R-410A refrigerant equipment.

WARNING

PERSONAL INJURY AND ENVIRONMENTAL

HAZARD

Failure to follow this warning could cause personal injury

or death.

Relieve pressure and recover all refrigerant before system

repair or final unit disposal.

Wear safety glasses and gloves when handling refrigerants.

Keep torches and other ignition sources away from refriger

-

ants and oils.

CAUTION

PERSONAL INJURY HAZARD

Failure to follow this caution may result in personal injury.

Sheet metal parts may have sharp edges or burrs. Use care

and wear appropriate protective clothing, safety glasses and

gloves when handling parts and servicing air conditioning

equipment.

MODEL NUMBER

RATED INDOOR AIRFLOW (CFM)

50JC**04

1125

50JC**05

1430

50JC**06

2000

Содержание WeatherExpert Puron 50JC04





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды