Carrier WeatherExpert 48LC B14 Series Скачать руководство пользователя страница 35

Страница: 35 / 56

Fig. 49 — HACR Caution Label

FACTORY-OPTION THRU-BASE CONNECTIONS
All units are equipped with the ability to bring utilities through the

base.
Gas is brought up through an embossed area located in the gas

section behind the gas entrance post. Access is gained through the

gas access panel. A knock out must be removed to accomplish

this.
The electrical entrance is located in the control box area and can

be accessed through the control box access panel. An embossed

area is provided with three knock outs. High voltage is brought

through the multi knock out by removing the appropriate size for

the size of the fitting required. A

-in. knock out is provided for

low voltage. An additional

-in. knock out is provided for a 115 v

line which is used when the unit is equipped with the non-unit

powered convenience outlet option.
All required fittings are field supplied. Install fittings when access

to both top and bottom of the base pan is available. See electrical

and gas connections for routing and connection information.
UNITS WITHOUT THRU-BASE CONNECTIONS
1. Install liquid tight conduit between disconnect and control

box.

2. Pull correctly rated high voltage wires through the conduit.
3. Install power lines to terminal connections as shown in

Fig. 44.

UNIT WITHOUT THRU-BASE CONNECTION KIT
Correctly rated low voltage wire can be routed through the rubber

grommet located on the corner post adjacent to the control box ac-

cess panel. Route wire through the grommet and then route the

wire behind the corner post utilizing the factory provided wire ties

secured to the control box. This will insure separation of the field

low voltage wire and the high voltage circuit. Route the low volt-

age wire to the Integrated Staging Control (ISC) board. See

Fig. 50.
NOTE: If utilizing the through the base connections, route the low

voltage wire through the wire ties to the Integrated Staging Con-

trol (ISC) board (see Fig. 51).

Fig. 50 — Field Control Wiring Raceway

HEAT ANTICIPATOR SETTINGS
Set heat anticipator settings at 0.14 amp for the first stage and

0.14 amp for second-stage heating.
TRANSFORMER CONNECTION FOR 208-V POWER

SUPPLY
All units except 208/230-v units are factory wired for the voltage

shown on the nameplate. If the 208/230-v unit is to be connected

to a 208-v power supply, the control transformer must be rewired

by moving the black wire with the

-in. female spade connector

from the 230-v connection and moving it to the 208-v

-in. male

terminal on the primary side of the transformer. Refer to unit label

diagram for additional information.

VAV-RTU Open Controller

For details on VAV-RTU Open option, refer to the

48/50LC*B 7-

26 VAV-RTU Open Controller Controls, Start-up, Operation and

Troubleshooting

manual.

RUBBER

GROMMET

CORNER

POST

WIRE

TIES

THRU THE BASE

CONNECTION

Содержание WeatherExpert 48LC B14 Series

























































Результаты поиска

Содержание WeatherExpert 48LC B14 Series

Отзывы:

Бренды по названию

Популярные бренды

Carrier WeatherExpert 48LC B14 Series, Руководство по установке

Результаты поиска

Содержание WeatherExpert 48LC B14 Series

Отзывы:

Бренды по названию

Популярные бренды