Carrier WeatherExpert 48LC B14 Series Скачать руководство пользователя

Страница: 26 / 56

Fig. 27 — Hood Part Identification and Seal Strip

Application Areas

Fig. 28 — Outdoor Air Screen Installation

Fig. 29 — Completed Hood Assembly

Step 10 — Economizer - Horizontal Airflow Units

The barometric relief damper ships attached to the exterior re-

turn opening panel on the unit (see Fig. 30). Remove shipping

cover to access the barometric relief damper, rain angle, and

parts bag. These items are to be repositioned on the side of the

field supplied ductwork. In addition, the barometric relief hood

should be used and can be ordered separately (PN: CRBAR-

HOD001A00) or can be field supplied.

Fig. 30 — Barometric Relief Damper

(Shipping Location)

Step 11 — Install Flue Hood and Combustion Air
Hood

The flue hood is shipped screwed to the fan deck inside the burner

compartment. Remove the burner access panel and then remove

the flue hood from its shipping location. Using the screws provid-

ed, install flue hood in the location shown in Fig. 31.
The combustion air hood is attached to the back of the burner ac-

cess panel. Remove the two screws securing the hood to the back

of the burner access panel. Using the two screws, re-attach the

hood to the front of the burner access panel as shown in Fig. 31.

Fig. 31 — Flue Hood and Combustion Air Hood

Details

Step 12 — Install Gas Piping

Installation of the gas piping must be in accordance with local

building codes and with applicable national codes. In U.S.A., refer

to NFPA 54/ANSI Z223.1 National Fuel Gas Code (NFGC). In

Canada, installation must be accordance with the CAN/CSA

B149.1 and CAN/CSA B149.2 installation codes for gas burning

appliances. This unit is factory equipped for use with natural gas

(NG) fuel at elevations up to 2000 ft (610 m) above sea level. Unit

may be field converted for operation at elevations above 2000 ft

APPLY SEAL STRIP
TO THE FRONT OF
THIS FLANGE

APPLY SEAL STRIP
TO THE BACK
OF THIS FLANGE

ITEM #

DESCRIPTION

QTY

Filter Supports

Central Retainer

Hood Top

Left Hood Side

Right Hood Side

Side Retainer

Top Diverters

Deflector

1. INSERT
AIR SCREEN

2. SLIDE
INTO
POSITION

SHIPPING

COVER

BAROMETRIC

RELIEF

DAMPER

RETURN

OPENING

PANEL

RAIN ANGLE

FLUE HOOD

COMBUSTION

AIR HOOD

Содержание WeatherExpert 48LC B14 Series

























































Результаты поиска

Содержание WeatherExpert 48LC B14 Series

Отзывы:

Похожие инструкции для WeatherExpert 48LC B14 Series

Бренды по названию

Популярные бренды

Carrier WeatherExpert 48LC B14 Series, Руководство по установке

Результаты поиска

Содержание WeatherExpert 48LC B14 Series

Отзывы:

Похожие инструкции для WeatherExpert 48LC B14 Series

Бренды по названию

Популярные бренды