Carrier TruVu TV-MPCXP1628-NR Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 94

background image

Addressing the TV-MPCXP1628-NR

TruVu™ MPC Controller (

part no. TV-MPCXP1628-NR)

CARRIER CORPORATION ©2021

Installation and Start-up Guide

All rights reserved

22

For the Open controllers connected to the TV-MPCXP1628-NR

•

BACnet MSTP Device Instance Number = BACnet MSTP Network yy

•

BACnet ARCNET Device Instance Number = BACnet ARCNET Network yy

•

BACnet MSTP Device Instance Name = the name "device" + Device Instance

•

BACnet ARCNET Device Instance Name = the name "device" + Device Instance

•

BACnet MSTP or ARCNET MAC Address = yy

•

BACnet MSTP Network Number = 161xx (learned from the router, defaults to 16101 if no TV-MPCXP1628-NR

is operating)

NOTES

•

Do not configure the rotary switches on the TV-MPCXP1628-NR to a number greater than 127 unless Port S1
is enabled for ARCNET. Doing so will not allow the i-Vu® server to discover the TV-MPCXP1628-NR.
If you change the TV-MPCXP1628-NR's switches or jumpers, you must cycle its power for the changes to take

effect.

•

If the BACnet automatic settings need to be changed, see

To communicate through the Local Access port

(page 69).

To set up BACnet Broadcast Management Devices (BBMDs)

If your system has multiple routers that reside on different IP subnets, you must set up one router on each IP

subnet as a BACnet/IP Broadcast Management Device (BBMD).

«
...
26
27
28
29
30
...
»

Содержание TruVu TV-MPCXP1628-NR































































































Отзывы:

Нет отзывов

Похожие инструкции для TruVu TV-MPCXP1628-NR

Бренд: Panasonic Страницы: 72

Бренд: Panasonic Страницы: 45

Бренд: Panasonic Страницы: 24

Бренд: Farfisa Страницы: 20

Бренд: Racal Instruments Страницы: 64

Бренд: Febco Страницы: 12

Бренд: HANYOUNG NUX Страницы: 74

Бренд: HANYOUNG NUX Страницы: 36

Бренд: HANYOUNG NUX Страницы: 2

Бренд: HANYOUNG NUX Страницы: 4

Бренд: MADRIX Страницы: 91

Бренд: MADRIX Страницы: 36

Бренд: MADRIX Страницы: 40

Бренд: YASKAWA Страницы: 18

Бренд: IAI Страницы: 5

GRAVIMETRIC AUGER FEEDER MGF-ST

Бренд: Maguire Products Страницы: 47

Бренд: Magtrol Страницы: 160

Бренд: WAM Страницы: 62

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды