manualshive.com logo in svg

Carrier Performance 40MBDQ09---3, Руководство по установке, Страница: 15 / 30

Поделиться
Скачать
Carrier Performance 40MBDQ09---3 Скачать руководство пользователя страница 15

IM-40MBDQ-05                                                                            Specifications subject to change without notice.                                                                                         

15

WIRING

Size all wires per the NEC (National Electrical Code) or CEC

(Canadian Electrical Code) and local codes. Use the electrical

data from the outdoor unit (MCA - minimum circuit amps and

MOCP - maximum over current protection), to correctly size

the wires and the disconnect fuse or breakers respectively.

SIZES 09-24 RECOMMENDED CONNECTION METHOD 

FOR POWER AND COMMUNICATION WIRING
Power and Communication Wiring:

 The main power is

supplied to the outdoor unit. The field supplied 14/3 power/

communication wiring, from the outdoor unit to the indoor

unit, consists of four (4) wires and provides the power for the

indoor unit. Two wires are high voltage AC power, one is

communication wiring and the other is a ground wire.

To minimize communication interference:

 If installed in a

high Electromagnetic field (EMF) area and communication

issues arise, a 14/2 stranded shielded wire can be used to

replace L2 and (S) between the outdoor and indoor units -

landing the shield onto the ground in the outdoor unit only.

Table 7 — Wiring Sizes 09-24 

SIZES 36-58 RECOMMENDED CONNECTION METHOD 

FOR POWER AND COMMUNICATION WIRING
Power and Communication Wiring:

 The main power is

supplied to the outdoor unit. The field supplied power wiring

from the outdoor unit to the indoor unit consists of three (3)

wires and provides the power for the indoor unit. Two wires

are high voltage AC power and one is a ground wire. To

minimize voltage drop, the factory recommended wire size is

14/2 stranded with a ground.

Communication Wiring:

 A separate shielded stranded copper

conductor only, with a 600 volt rating and double insulated

copper wire, must be used as the communication wire from the

outdoor unit to the indoor unit.
Please use a separate shielded 16GA stranded control wire.

Table 8 — Wiring Sizes 36-58

CABLE

CABLE SIZE

REMARKS

Connection 

Cable

14AWG

3 wire + Ground 1

Φ

 208/230 V 

(Stranded wire is 

recommended)

CABLE

CABLE SIZE

REMARKS

Power 

Connection 

Cable

14AWG

2 wire + Ground 1

Φ

 208/230 V

Communication 

Cable

16AWG

2 wire stranded shielded control 

wire

EQUIPMENT DAMAGE HAZARD

Be sure to comply with local codes while running wire from the 
indoor unit to the outdoor unit.
Every wire must be connected firmly. Loose wiring may cause the 
terminal to overheat or result in a unit malfunction. A fire hazard 
may also exist. Ensure all wiring is tightly connected.
No wire should touch the refrigerant tubing, compressor or any 
moving parts.
Disconnecting means must be provided and located within sight 
and readily accessible from the system.
Route the connecting cable with conduit through the hole in the 
conduit panel.

CAUTION

Содержание Performance 40MBDQ09---3































Отзывы:

Нет отзывов