manualshive.com logo in svg

Carrier P, Руководство пользователя, Страница: 37 / 40

Поделиться
Скачать
Carrier P Скачать руководство пользователя страница 37

37

ACCESSORIES

*Extended metal wall sleeve also available in 26 in. and 28 in. depth.

†Custom colors are also available.

ACCESSORY

FORM NUMBER

PART NUMBER

DESCRIPTION

Wall Sleeves

52S-48SI

WALL-SLEEVE-1PK

Non-Insulated Plastic Wall Sleeve, 1 per pack

WALL-SLEEVE-9PK

Non-Insulated Plastic Wall Sleeve, 9 per pack

SLEEVE-INSUL-1PK

Insulated Plastic Wall Sleeve, 1 per pack

52S-50SI

SLEEVE-STEEL-1PK

Insulated Metal Wall Sleeve, 1 per pack

52S-49SI*

SLEEVE-EXT24-1PK

Extended Metal Wall Sleeve for Deep Wall Applications (24 in. deep), 1 per pack

52C,P-12SI

FR-SLEEVE-EXT

Friedrich wall sleeve extension to retrofit Carrier PTAC unit into Friedrich 11

1

/

2

" deep (T Series) wall 

sleeve. 1 per pack

Exterior Grilles†

52S-59SI

GRILLE-ALU-STAMP

Stamped Aluminum Exterior Grille, Clear Finish

52S-58SI

GRILLE-PLA-BROWN

Plastic Architectural Rear Grille, Brown

GRILLE-PLA-BEIGE

Plastic Architectural Rear Grille, Beige

52S-60SI

GRILLE-ALU-CLEAR

Aluminum Architectural Exterior Grille, Clear Finish

GRILLE-ALU-WHITE

Aluminum Architectural Exterior Grille, White

GRILLE-ALU-BRONZ

Aluminum Architectural Exterior Grille, Light Bronze

GRILLE-ALU-MBRNZ

Aluminum Architectural Exterior Grille, Medium Bronze

GRILLE-ALU-BROWN

Aluminum Architectural Exterior Grille, Brown (Dark Bronze)

GRILLE-ALU-BEIGE

Aluminum Architectural Exterior Grille, Beige

GRILLE-ALU-ALPIN

Aluminum Architectural Exterior Grille, Alpine (matches Carrier Wall Sleeve)

GRILLE-ALU-PEACH

Aluminum Architectural Exterior Grille, Peach

GRILLE-ALU-MELON

Aluminum Architectural Exterior Grille, Melon

GRILLE-ALU-LGREY

Aluminum Architectural Exterior Grille, Light Grey

GRILLE-ALU-SGREY

Aluminum Architectural Exterior Grille, Slate Gray

GRILLE-ALU-RDBRK

Aluminum Architectural Exterior Grille, Red Brick

GRILLE-ALU-BLUE

Aluminum Architectural Exterior Grille, Blue

GRILLE-ALU-GREEN

Aluminum Architectural Exterior Grille, Green

Subbase

52C,P-1SI

SUBBASE-NON-ELEC

Non-electrical Subbase

52C,P-2SI

SUBBASE-230V-15A

Electrical subbase with factory-installed 208/230V, 15 amp receptacle 

SUBBASE-230V-20A

Electrical subbase with factory-installed 208/230V, 20 amp receptacle 

SUBBASE-230V-30A

Electrical subbase with factory-installed 208/230V, 30 amp receptacle 

SUBBASE-265V-15A

Electrical subbase with factory-installed 265V, 15 amp receptacle 

SUBBASE-265V-20A

Electrical subbase with factory-installed 265V, 20 amp receptacle 

SUBBASE-265V-30A

Electrical subbase with factory-installed 265V, 30 amp receptacle 

52C,P-3SI

SUBBASE-HARDWIRE

Electrical subbase with factory-installed hardwire kit (230/208V and 265V)

Subbase

Field-Installed

Kits

52C,P-4SI

SUBBASE-SWITCH

Field-Installable Switch kit for an electrical subbase

52C,P-5SI

SUBBASE-FUSE-15A

Field-Installed Fuse Kit (15 amp) for electrical subbase

SUBBASE-FUSE-20A

Field-Installed Fuse Kit (20 amp) for electrical subbase

SUBBASE-FUSE-30A

Field-Installed Fuse Kit (30 amp) for electrical subbase

Electrical 

Connections

52C,P-11SI

HARDWIRE-KIT-1PK

Permanent power connection to the unit (includes 36" of flexible conduit and unit-mounted
connector, 230/208V and 265V) 1 per pack

52C,P-19SI

CONDUIT-INTF-4PK

Interface kit for field-supplied conduit to provide permanent power connection (230/208V and 265V) to 
the unit. Kit includes Molex connector for easy connect/disconnect. 4 per pack

Condensate 

Drain Kit

52S-53SI

DRAIN-KIT-4PK

Attaches to wall sleeve for controlled internal or external disposal of condensate 4 per pack

Wall

Thermostats

N/A

HH01AD045

Electro-mechanical Wall Thermostat (Heat/Cool and Heat Pump)

TSTATCCBPC01-B

Value Series Electronic Thermostat w/Digital display (Heat/Cool Models)

TSTATCCBPH01-B

Value Series Electronic Thermostat w/Digital display (Heat Pump Models)

TSTATCCPAC01-B

7-Day Programmable Electronic Thermostat (Heat/Cool Models)

TSTATCCPHP01-B

7-Day Programmable Electronic Thermostat (Heat Pump Models)

Wall Thermostat

Interface

Retrofit Kit

52C,P-7SI

RC-FIELDKIT230HC

Field-installed wall thermostat retrofit kit to convert a standard 230V Heat/Cool unit to an
RC unit. Wall thermostat sold separately (can be used to convert a cool only unit to RC).

RC-FIELDKIT230HP

Field-installed wall thermostat retrofit kit to convert a standard 230V Heat Pump unit to an
RC unit. Wall thermostat sold separately.

RC-FIELDKIT265HC

Field-installed wall thermostat retrofit kit to convert a standard 265V Heat/Cool unit to an
RC unit. Wall thermostat sold separately (can be used to convert a cool only unit to RC).

RC-FIELDKIT265HP

Field-installed wall thermostat retrofit kit to convert a standard 265V Heat Pump unit to a
 RC unit. Wall thermostat sold separately.

N/A

TSTAT-COVER-6X7

Clear plastic locking thermostat cover prevents unauthorized access to thermostat. Cover for use with 
non-programmable and electro-mechanical thermostats. Outside dimensions: 6

1

/

2

" x 7

1

/

2

" x 2

15

/

16

". 

1 per pack

N/A

TSTAT-COVER-7X10

Clear plastic locking thermostat cover prevents unauthorized access to thermostat. Cover for use with 
programmable thermostats. Outside dimensions: 7

1

/

4

" x 9

3

/

4

" x 3

3

/

8

". 1 per pack

Replacement

Filters

N/A

AIR-FILTER-10PK

Replacement air filters in package of 10

Energy 

Management

52C,P-10SI

EM-KIT

Allows unit to be turned on and off from a remote location (includes freeze guard protection)

Locking Security 

Control Door 

52C,P-13SI

SECURITY-DOOR

Key-locking security door to prevent access to heating and cooling controls

Lateral Duct Kit

52C,P-14SI

LATERAL-DUCT

Ductwork to allow one unit to heat and cool two rooms (plenum plus extension duct and registers)

Air/Curtain

Deflector

52C,P-9SI

DEFLECTOR-1PK

Lateral air deflector, with individually adjustable louvers, to enhance air circulation, 1 per pack

N/A

CURTDFL-52CP-1PK

Curtain deflector for 52C and 52P models — prevents curtains from blowing into discharge air stream. 
1 per pack.
NOTE: Curtain deflector for previous models are also available. Contact Carrier Representative.

Содержание P









































Отзывы:

Нет отзывов