Carrier NSB-LDT4-PS-BB Скачать руководство пользователя страница 3

Страница: 3 / 8

Catalog No. 11-808-639-01

3 of 8

Specifications subject to change without notice.

Water Leak Detector

Installation and Troubleshooting

#26268

– 02

/28/2020

Specifications

Power

24VAC +/- 10%

5 Amp Relays

4 VA max

Wiring

Flex connector or liquid-tight fitting

Relays

Up to 6 wires

Transmitter

2 wires for Power

Mounting

Lays in the pan or attached with a pan

edge hook with screws

Sensor

Standard

Single SS probe from bottom of BB with

adjustable depth screw from .063” to
.84”

Optional

Remote spot water sensor with depth
screw with adjustable depth from
1/16” to l/2”

Optional

Remote rope water sensor
Detects water over the full length at
depths >0.125”.

NOTE

100 ft.

maximum including non-sensing
extension cable.

Detector Transmitter

Alarm Contacts Two SPDT, 5A relay outputs

SPDT, 30 VAC/DC max

Selectable as normally
Energized or De-energized

Indication

1 Green Power LED, 1 Red Alarm LED

Reset Action

If latching, local push button or power

interrupt

Sensor Reaction Responds to presence of water within 5

seconds

Termination

Terminal strip, 4-10 terminals, 12-24 AWG

Agency

RoHS, UL94V-0, UV-rated in Enclosure

Set Up

BB Sensor

Adjustable depth from .063” to

.84” (≈1/16th” default)

Remote Sensor

Adjustable depth from .063” to

.84” (≈1/16th” default)

Latching

Latching version - Stays

Jumper

energized after water has dried up

Non-latching version (default) -
Alarm follows wet or dry surface

Supervision

Supervised version (default) -

Jumper

De-energized when in alarm.

NOTE

Relay will drop out on loss

of power indicating a water
detection alarm.

Unsupervised version -
Energized when in alarm.

Enclosure Ratings

Transmitter

BB Box, NEMA 4

Remote Spot

Submersible, w/ FEP plenum-

Sensor

rated, waterproof cable

Rope Sensor

Plenum rated

Ambient

Transmitter (BB) -40 to 185ºF (-40 to 85ºC),

0 to 95%RH, Non-condensing

Remote Spot -40 to 185ºF (-40 to 85ºC),
Sensor

0 to 95%RH, Condensing

Rope Sensor

32 to 167ºF (0 to 75ºC),

0 to 95%RH, Non-condensing

Enclosure Materials

Transmitter (BB) Polycarbonate

Remote Sensor Aluminum bracket w/ ABS
plastic shell

Содержание NSB-LDT4-PS-BB









Результаты поиска

Содержание NSB-LDT4-PS-BB

Отзывы:

Похожие инструкции для NSB-LDT4-PS-BB

Бренды по названию

Популярные бренды

Carrier NSB-LDT4-PS-BB, Инструкция по установке и устранению неисправностей

Результаты поиска

Содержание NSB-LDT4-PS-BB

Отзывы:

Похожие инструкции для NSB-LDT4-PS-BB

Бренды по названию

Популярные бренды