Carrier N92ESN Скачать руководство пользователя

Страница: 48 / 66

N92ESN: Installation, Start-up, Operating and Service and Maintenance Instructions

Manufacturer reserves the right to change, at any time, specifications and designs without notice and without obligations.

1. Remove upper and middle collector box drain plugs opposite of the

condensate trap. See

Fig. 59

A11392

Fig. 59 – Priming Condensate Trap

2. Connect field-supplied 5/8-in. (16 mm) ID tube with attached

funnel to upper collector box drain connection.

3. Pour one quart (liter) of water into funnel/tube. Water should run

through collector box, overfill condensate trap, and flow into open

field drain.

4. Remove funnel; replace collector box drain plug.
5. Connect field-supplied 5/8-in. (16 mm) ID tube to middle collector

box drain port.

6. Pour one quart (liter) of water into funnel/tube. Water should run

through collector box, overfill condensate trap, and flow into open

field drain.

7. Remove funnel and tube from collector box and replace collector

box drain plug.

Purge Gas Lines

If not previously done, purge the lines after all connections have been

made and check for leaks.

Table 19

Adjustments

A93059

Fig. 60 – Orifice Hole

For proper operation and long term reliability, the Furnace input rate

must be /-2 percent of input rate on furnace rating plate, or as

adjusted for altitude.
The gas input rate on rating plate is for installations at altitudes up to

2000 ft. (609.6M).

CAUTION

UNIT OPERATION HAZARD

Failure to follow this caution may result in intermittent unit operation

or performance satisfaction.
Condensate trap must be PRIMED or proper draining may not occur.

The condensate trap has two internal chambers which can ONLY be

primed by pouring water into the inducer drain side of condensate trap.

WARNING

FIRE OR EXPLOSION HAZARD

Failure to follow this warning could result in personal injury, death,

and/or property damage.

Never purge a gas line into a combustion chamber. Never test for gas

leaks with an open flame. Use a commercially available soap solution

made specifically for the detection of leaks to check all connections. A

fire or explosion may result causing property damage, personal injury

or loss of life.

WARNING

FIRE HAZARD

Failure to follow this warning could result in personal injury, death

and/or property damage.

DO NOT bottom out gas valve regulator adjusting screw. This can

result in unregulated manifold pressure and result in excess overfire and

heat exchanger failures.

CAUTION

FURNACE DAMAGE HAZARD

Failure to follow this caution may result in reduced furnace life.
DO NOT redrill orifices. Improper drilling (burrs, out-of-round holes,

etc.) can cause excessive burner noise and misdirection of burner

flames. This can result in flame impingement of heat exchangers,

causing failures. See

Fig. 60

BURNER

ORIFICE

Содержание N92ESN



































































Результаты поиска

Содержание N92ESN

Отзывы:

Похожие инструкции для N92ESN

Бренды по названию

Популярные бренды

Carrier N92ESN, Инструкции по установке, запуску, эксплуатации, обслуживанию и техническому обслуживанию

Результаты поиска

Содержание N92ESN

Отзывы:

Похожие инструкции для N92ESN

Бренды по названию

Популярные бренды