manualshive.com logo in svg

Carrier Gemini 38AU07 Series, Руководство по установке

Поделиться
Скачать
Carrier Gemini 38AU07 Series Скачать руководство пользователя страница 38

38

Compressor Protection

COMPRESSOR OVER-TEMPERATURE PROTECTION
(IP)

A thermostat installed on the compressor motor winding

reacts to excessively high winding temperatures and shuts off

the compressor.
CRANKCASE HEATER

The heater minimizes absorption of liquid refrigerant by

oil in the crankcase during brief or extended shutdown peri-

ods. The heater is wired to cycle with the compressor; the

heater is off when compressor is running, and on when com-

pressor is off.

The crankcase heater will operate as long as the power cir-

cuit is energized. The main disconnect must be on to energize

the crankcase heater.

ADVANCED SCROLL TEMPERATURE PROTECTION

(ASTP)

See “Advanced Scroll Temperature Protection (ASTP)” on

page 24.
LOW-PRESSURE SWITCH

The 38AU low-pressure switch is stem-mounted on the

suction line. Switches are all fixed, non-adjustable type.
HIGH-PRESSURE SWITCH

The high-pressure switch is stem mounted on the dis-

charge line. The switch is a fixed, non-adjustable type.
OUTDOOR FANS

Each fan is supported by a formed-wire mount bolted to

the fan deck and covered with a wire guard. Fan motors have

permanently lubricated bearings.
1. Shut off unit power supply. Install lockout tag.
2. Remove outdoor fan assembly (grille, motor, and fan).

3. Loosen fan hub setscrews.

4. Adjust fan height as shown in Fig. 41.

5. Tighten setscrews to 84 in.-lbs (949 N-cm).

6. Replace outdoor fan assembly.

Fig. 41 — Outdoor Fan Blade Position

LUBRICATION

Fan Motors

The fan motors have sealed bearings. No provisions are

made for lubrication.

Compressor

The compressor has its own oil supply. Loss of oil due to a

leak in the system should be the only reason for adding oil af-

ter the system has been in operation.

ROUTINE CLEANING OF ROUND-TUBE PLATE FIN

(RTPF) COILS

Periodic cleaning with Totaline

®

 environmentally sound

coil cleaner is essential to extend the life of RTPF coils. This

cleaner is available from Carrier Replacement parts division

as part number P902-0301 for a one gallon container, and part

number P902-0305 for a 5 gallon container. It is recommend-

ed that all RTPF coils be cleaned with the Totaline environ-

mentally sound coil cleaner as described below. 

Coil cleaning should be part of the unit’s regularly sched-

uled maintenance procedures to ensure long life of the coil.

Failure to clean the coils may result in reduced durability in

the environment.

Avoid the use of:

• coil brighteners
• acid cleaning prior to painting
• high pressure washers
• poor quality water for cleaning

Totaline environmentally sound coil cleaner is non-flam-

mable, hypoallergenic, non-bacterial, and a USDA accepted

biodegradable agent that will not harm the coil or surround-

ing components such as electrical wiring, painted metal sur-

faces, or insulation. Use of non-recommended coil cleaners is

strongly discouraged since coil and unit durability could be

affected.
TOTALINE ENVIRONMENTALLY SOUND COIL

CLEANER APPLICATION EQUIPMENT

• 2 

1

/

2

 gallon garden sprayer

• water rinse with low velocity spray nozzle

Totaline Environmentally Sound Coil Cleaner Application 

Instructions:

NOTE: Proper eye protection such as safety glasses is recom-

mended during mixing and application.
1. Turn off unit power.
2. Remove screws holding rear corner post and top cover in

place. Pivot top cover up 12 to 18 inches (305 to 457

mm) and support with a rigid support. See Fig. 42.

IMPORTANT: Never open any switch or disconnect that

energizes the crankcase heater unless unit is being serviced

or is to be shut down for a prolonged period. After a pro-

longed shutdown on a service job, energize the crankcase

heater for 24 hours before starting the compressor.

3.6 mm +0/0/-0.8

CAUTION

UNIT DAMAGE HAZARD
Failure to follow this caution may result in corrosion and

damage to the unit.
Harsh chemicals, household bleach or acid or basic cleaners

should not be used to clean outdoor or indoor coils or any

kind. These cleaners can be very difficult to rinse out of the

coil and can accelerate corrosion at the fin/tube interface

where dissimilar materials are in contact. If there is dirt

below the surface of the coil use the Totaline environmen-

tally sound coil cleaner as described above.

IMPORTANT: High velocity water from a pressure

washer, garden hose, or compressed air should never be

used to clean a coil. The force of the water or air jet will

bend the fin edges and increase airside pressure drop,

resulting in reduced unit performance.

Содержание Gemini 38AU07 Series





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды