manualshive.com logo in svg

Carrier CRECOMZR077A00, Руководство по установке, Страница: 2 / 28

Поделиться
Скачать
Carrier CRECOMZR077A00 Скачать руководство пользователя страница 2

2

The EconoMi$er

®

 X system utilizes the latest technology avail-

able for integrating the use of free cooling with mechanical cool-

ing for packaged rooftop units. The code compliant Jade W7220

control system optimizes energy consumption, zone comfort,

and equipment cycling by operating the compressors when the

outdoor-air temperature is too warm, integrating the compressor

with outdoor air when free cooling is available, and locking out

the compressor when outdoor-air temperature is too cold. De-

mand controlled ventilation is supported.
This EconoMi$er X can be used with 1 or 2 speed indoor fan

motor units. (All other speed settings listed are for future use.)
The EconoMi$er X system utilizes gear-drive technology with a

direct-mount spring return actuator that will close upon loss of

power. The EconoMi$er X system comes standard with fault de-

tection and diagnostics (FDD), an outdoor air temperature sen-

sor, and mixed air temperature sensor (also called supply air

temperature sensor). Outdoor enthalpy, indoor (return) dry bulb

or enthalpy, and CO

2

 sensors are available for field installation.

Standard integrated barometric relief dampers provide natural

building pressurization control. An optional power exhaust

system is available for applications requiring even greater ex-

haust capabilities. The power exhaust set point is adjustable at

the EconoMi$er X controller.
See Table 1-3 for package usage. See Table 4 for package con-

tents. See Table 5 for sensor usage.

IMPORTANT: Read these instructions completely before at-

tempting to install accessory economizer.

Table 1 — Carrier Package Usage

MODEL NUMBER

ECONOMI$ER X

PART NUMBER

Small Cabinet

48/50FC 04-07

48/50GC 04-06

48/50HC, LC 04-06

48/50TC 04-07

50TCQ 04-07

50HCQ 04-06

50KCQ04-06

48/50KC 04-06

CRECOMZR077A00

Large Cabinet

48/050HC 07-12

48/50LC 07

48/50TC 08-14

50TCQ 08-12

50HCQ 07-09

CRECOMZR079A00

Extra Large Cabinet

48/50HC 14

48/50LC 08-12

48/50TC 16

50TCQ 14

50HCQ 12

CRECOMZR081A00

Table 2 — Bryant Package Usage

MODEL NUMBER

ECONOMI$ER X

PART NUMBER

Small Cabinet

581K/551K 04-06

582K/559K 04-07

581J/551J 04-06

549J/547J/559J/582J 04-06

548J/580J/558J 04-07

CRECOMZR077A00

Large Cabinet

581J/551J 07-12

580J/558J 08-14

548J 08-12

549J 07-09

CRECOMZR079A00

Extra Large Cabinet

581J/551J 14

580J/558J 16

548J 14

549J 12

CRECOMZR081A00

Table 3 — ICP Package Usage

MODEL NUMBER

ECONOMI$ER X

PART NUMBER

Small Cabinet

RAV/RGV 036-072

RAW/RGW 036-060

RAH/RGH 036-060

RAS/RGS 036-072

RHS 036-072

RHX/RHH 036-060

RAX/RGX 036-060

CRECOMZR077A00

Large Cabinet

RAH/RGH 072-120

RAS/RGS 090-150

RHH 072-102

RHS 090-120

CRECOMZR079A00

Extra Large Cabinet

RAH/RGH 150

RAS/RGS 180

RHS 150

RHH 120

CRECOMZR081A00

Содержание CRECOMZR077A00





























Отзывы:

Нет отзывов