Carrier CRECOMZR052A00 Скачать руководство пользователя страница 23

Страница: 23 / 24

DCV Minimum and Maximum Position

To check the DCV minimum and maximum position:

1. Make sure EconoMi$er IV preparation procedure has been

performed.

2. Connect a 9-v battery to AQ (positive node) and AQ1

(negative node). The DCV LED should turn on. The actuator

should drive to between 90 and 95% open.

3. Turn the DCV Maximum Position potentiometer to midpoint.

The actuator should drive to between 20 and 80% open.

4. Turn the DCV Maximum Position potentiometer to fully

CCW. The actuator should drive fully closed.

5. Turn the Minimum Position potentiometer to midpoint. The

actuator should drive to between 20 and 80% open.

6. Turn the Minimum Position potentiometer fully CW. The

actuator should drive fully open.

7. Remove the jumper from TR and N. The actuator should

drive fully closed.

8. Return EconoMi$er IV settings and wiring to normal after

completing troubleshooting.

Supply-Air Input

To check supply-air input:

1. Make sure EconoMi$er IV preparation procedure has been

performed.

2. Set the Enthalpy potentiometer to A. The Free Cool LED

turns on. The actuator should drive to between 20 and 80%

open.

3. Remove the 5.6 kilo-ohm resistor and jumper T to T1. The

actuator should drive fully open.

4. Remove the jumper across T and T1. The actuator should

drive fully closed.

5. Return EconoMi$er IV settings and wiring to normal after

completing troubleshooting.

EconoMi$er IV Troubleshooting Completion

This procedure is used to return the EconoMi$er IV to operation.

No troubleshooting or testing is done by performing the following

procedure:

1. Disconnect power at TR and TR1.

2. Set enthalpy potentiometer to previous setting.
3. Set DCV maximum position potentiometer to previous set

ting. Note: when not using a CO

sensor the DCV Max

potentiometer must be fully closed (CCW) for the Minimum

Position potentiometer to function correctly.

4. Set minimum position, DCV set point, and exhaust potenti

ometers to previous settings.

5. Remove 620-ohm resistor from terminals SR and +.
6. Remove 1.2 kilo-ohm checkout resistor from terminals SO

and +. If used, reconnect sensor from terminals SO and +.

7. Remove jumper from TR to N.
8. Remove jumper from TR to 1.
9. Remove 5.6 kilo-ohm resistor from T and T1. Reconnect

wires at T and T1

Содержание CRECOMZR052A00

























Результаты поиска

Содержание CRECOMZR052A00

Отзывы:

Похожие инструкции для CRECOMZR052A00

Бренды по названию

Популярные бренды

Carrier CRECOMZR052A00, Руководство по установке

Результаты поиска

Содержание CRECOMZR052A00

Отзывы:

Похожие инструкции для CRECOMZR052A00

Бренды по названию

Популярные бренды