Carrier 69NT40-541-505 Скачать руководство пользователя страница 74 | Manualshive

Страница: 74 / 143

Carrier 69NT40-541-505 Скачать руководство пользователя страница 74

T-368

4–44

P7 Tests - High Pressure Tests:

Unit is run at full capacity without condenser fan running to make sure that the

HPS opens and closes properly.

P7-0

High Pressure Switch
Closed

With the unit running, the condenser fan is de-energized, and a 15 minute timer is
started. The right display shows discharge pressure if the unit is equipped with a
discharge pressure transducer (DPT). If no DPT is installed, the condenser pres-
sure transducer (CPT) reading will be displayed.
Test is skipped if:

Sensed ambient temperature is less than 7



C (45



F)

Return air temperature is less than 17.8



C (0



F)

The water pressure switch (WP) is open, indicating that the unit is operat-
ing with a water-cooled condenser

Test is skipped if the unit does NOT have:

A compressor discharge sensor (CPDS)
A discharge pressure transducer (DPT)
A condenser pressure transducer (CPT)

Test passes if the HPS opens within 15 minutes.
Test immediately fails if the following inputs are sensed to be invalid:

Compressor discharge sensor (CPDS)
Discharge pressure transducer (DPT)
Condenser pressure transducer (CPT)
Return temperature sensor (RTS)
Ambient sensor (AMBS)

Test will also fail if:

HPS fails to open within 15 minutes
Discharge temperature exceeds 138



C (280



F)

Discharge temperature is less than or equal to ambient temperature plus
5



C (9



F)

CPT or DPT pressure exceeds 27.42kg/cm

2

(390psig)

P7-1

High Pressure Switch
Open

Test P70 must pass for P71 to execute.
The condenser fan is started and a 60 second timer is started.
Test passes if the high pressure switch (HPS) closes within the 60-second time
limit, otherwise, it fails.

P8 Tests Perishable Mode Tests:

Pretrip tests P70 and P71 must have passed or have been skipped for these

tests to execute.

P8-0

Perishable Mode
Heat Test

If the container temperature is below 15.6



C (60



F), the set point is changed to

15.6



C, and a 60-minute timer is started. The left display will read P80. The control

will then heat the container until 15.6



C is reached.

If the container temperature is above 15.6



C at the start of the test, then the test

proceeds immediately to test P81 and the left display will change to P81.
The test fails if the 180-minute timer expires before the control temperature reach-
es set point. The display will read P80, FAIL.

Table 4–7 Controller Pre-Trip Test Codes

Downloaded from

«
...
72
73
74
75
76
...
»

Содержание 69NT40-541-505
















































































































































Отзывы:

Нет отзывов