Carrier 59SP6A Скачать руководство пользователя

Страница: 65 / 74

59SP6A: Installation, Start-up, Operating, Service and Maintenance Instructions

Manufacturer reserves the right to change, at any time, specifications and designs without notice and without obligations.

a. Perform component self-test as shown at the bottom of the

SERVICE label, located on the blower door.

b. Verify blower is rotating in the correct direction

18. If furnace is operating properly, RELEASE BLOWER DOOR

SWITCH. Remove any jumpers or reconnect any disconnected

thermostat leads. Replace blower door.

19. Turn on gas supply and cycle furnace through one complete heating

cycle. Verify the furnace temperature rise as shown in Adjustments

Section. Adjust temperature rise as shown in Adjustments Section.

Cleaning Burners and Flame Sensor

The following items must be performed by a qualified service

technician. If the burners develop an accumulation of light dirt or dust,

they may be cleaned by using the following procedure:

NOTE:

Use a back-up wrench on the gas valve to prevent the valve

from rotating on the manifold or damaging the mounting to the burner

assembly.
Refer to

Fig. 70

A11403

Fig. 70 – Burner Assembly

1. Disconnect power at external disconnect, fuse or circuit breaker.
2. Turn off gas at external shut-off or gas meter.
3. Remove control door and set aside.
4. Turn electric switch on gas valve to OFF.
5. Disconnect the gas pipe from gas valve and remove pipe from the

furnace casing.

6. Remove individual wires from terminals on gas valve.
7. Disconnect Hot Surface Igniter (HSI) wires from HSI.
8. Disconnect Flame Sensor wire from Flame Sensor.
9. Support the manifold and remove the 4 screws that secure the

manifold assembly to the burner assembly and set aside. Note the

location of the green/yellow wire and ground terminal.

10. Inspect the orifices in the manifold assembly for blockages or

obstructions. Remove orifice and clean or replace orifice.

11. Remove the four screws that attach the top plate of the casing to the

furnace.

12. Raise top plate up slightly and prop it up with a small piece of wood

or folded cardboard.

13. Support the burner assembly and remove the screws that attach the

burner assembly to the heat exchanger cell panel.

14. Remove wires from both rollout switches.
15. Slide one-piece burner out of slots on sides of burner assembly.
16. Remove the flame sensor from the burner assembly.
17. (Optional) Remove the Hot Surface Igniter (HSI) and bracket from

the burner assembly.

18. Check igniter resistance. Nominal resistance is 40 to 70 ohms at

room temperature and is stable over the life of the igniter.

19. Clean burner with a brush and a vacuum.
20. Clean the flame sensor with fine steel wool (0000 grade). Do not

use sand paper or emery cloth.

To reinstall burner assembly:

1. Install the Hot Surface Igniter (HSI) and bracket in burner

assembly.

2. Install flame sensor on burner.
3. Align the edges of the one-piece burner with the slots in the burner

assembly and slide the burners forward until they are fully seated in

the burner assembly.

4. Align the orifices in the manifold assembly with the support rings

on the end of the burner.

5. Insert the orifices in the support rings of the burners.

NOTE:

If manifold does not fit flush against the burner, do not force the

manifold on the burner assembly. The burners are not fully seated

forward in the burner assembly. Remove the manifold and check burner

positioning in the burner assembly before re-installing the manifold.

6. Attach the green/yellow wire and ground terminal to one of the

manifold mounting screws.

7. Install the remaining manifold mounting screws.
8. Check the igniter alignment. See

Fig. 70

Fig. 71

, and

Fig. 72

9. Attach the wires to the roll-out switches.
10. Align the burner assembly with the openings in the primary cell

inlet panel and attach the burner assembly to the cell panel.

11. Connect the wire for the flame sensor.
12. Connect the wire for the Hot Surface Igniter.

NOTE:

Use propane-resistant pipe dope to prevent leaks. Do not use

PTFE thread-seal tape.

13. Install the gas pipe to the gas valve.

A11405

Fig. 71 – Igniter Position - Top View

WARNING

ELECTRICAL SHOCK AND FIRE HAZARD

Failure to follow this warning could result in personal injury, death,

and/or property damage.

Turn off the gas and electrical supplies to the furnace and install lockout

tag before performing any maintenance or service. Follow the operating

instructions on the label attached to the furnace.

FLAME SENSOR
(BELOW BURNER)

FLAME ROLLOUT
SWITCH

BRACKET, IGNITER

IGNITER

BURNER SUPT. ASSY

BURNER ASSY

WARNING

FIRE OR EXPLOSION HAZARD

Failure to follow this warning could result in personal injury death,

and/or property damage.

Never purge a gas line into a combustion chamber. Never test for gas

leaks with an open flame. Use a commercially available soap solution

made specifically for the detection of leaks to check all connections. A

fire or explosion may result causing property damage, personal injury

or loss of life.

2-1/2-in.

(64.4)

1-1/4-in.

(31.8)

Содержание 59SP6A











































































Результаты поиска

Содержание 59SP6A

Отзывы:

Похожие инструкции для 59SP6A

Бренды по названию

Популярные бренды

Carrier 59SP6A, Инструкции по установке, запуску, эксплуатации, обслуживанию и техническому обслуживанию

Результаты поиска

Содержание 59SP6A

Отзывы:

Похожие инструкции для 59SP6A

Бренды по названию

Популярные бренды