Carrier 58TMA Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 18

Carrier 58TMA Скачать руководство пользователя страница 16

(2.) Derate for altitude if applicable.

(3.) Return and supply ducts for excessive restrictions

causing static pressures greater than 0.50-in. wc.

c. Adjust air temperature rise by adjusting blower speed.

Increase blower speed to reduce temperature rise. Decrease
blower speed to increase temperature rise. For high fire,
speed selection can be med-high or med-low (factory

setting). For low fire, speed tap selection can be low
(factory setting) or med-low if high-fire speed selection is
med-high.

Disconnect the electrical power before changing the speed
tap. A failure to follow this warning can cause personal injury
or death.

d. To change motor speed selection for high heat, remove

blower motor lead from control HIGH-GAS-HEAT termi-
nal (See Fig. 11. and Fig. 15.). Select desired blower motor
speed lead from one of the other terminals and relocate it to
the HIGH-GAS-HEAT terminal. See Table 10 for lead
color identification. Reconnect original lead to the PARK
terminal. Follow this same procedure for proper selection
of cool and low-gas-heat speed selection.

Table 9—Gas Rate (Cu Ft/Hr)

SECONDS

FOR 1

REVOLUTION

SIZE OF TEST DIAL

SECONDS

FOR 1

REVOLUTION

SIZE OF TEST DIAL

1

cu ft

2

cu ft

5

cu ft

1

cu ft

2

cu ft

5

cu ft

10
11
12
13
14

360
327
300
277
257

720
655
600
555
514

1800
1636
1500
1385
1286

50
51
52
53
54

72
71
69
68
67

144
141
138
136
133

360
355
346
340
333

15
16
17
18
19

240
225
212
200
189

480
450
424
400
379

1200
1125
1059

100
947

55
56
57
58
59

65
64
63
62
61

131
129
126
124
122

327
321
316
310
305

20
21
22
23
24

180
171
164
157
150

360
343
327
313
300

900
857
818
783
750

60
62
64
66
68

60
58
56
54
53

120
116
112
109
106

300
290
281
273
265

25
26
27
28
29

144
138
133
129
124

288
277
267
257
248

720
692
667
643
621

70
72
74
76
78

51
50
48
47
46

103
100

97
95
92

257
250
243
237
231

30
31
32
33
34

120
116
113
109
106

240
232
225
218
212

600
581
563
545
529

80
82
84
86
88

45
44
43
42
41

90
88
86
84
82

225
220
214
209
205

35
36
37
38
39

103
100

97
95
92

206
200
195
189
185

514
500
486
474
462

90
92
94
96
98

40
39
38
38
37

80
78
76
75
74

200
196
192
188
184

40
41
42
43
44

90
88
86
84
82

180
176
172
167
164

450
439
429
419
409

100
102
104
106
108

36
35
35
34
33

72
71
69
68
67

180
178
173
170
167

45
46
47
48
49

80
78
76
75
73

160
157
153
150
147

400
391
383
375
367

110
112
116
120

33
32
31
30

65
64
62
60

164
161
155
150

Fig. 16—Redundant Automatic Gas Control Valve

A93376

LOW-FIRE
ADJUSTMENT
ALLEN SCREW
(UNDER CAP)

HIGH-FIRE
ADJUSTMENT
ALLEN SCREW
(UNDER CAP)

MANUAL
ON/OFF

INLET
PRESSURE
TAP

MANIFOLD

PRESSURE

TAP

Fig. 17—Burner Flame

A89020

Table 10—Speed Selection

COLOR

SPEED

AS SHIPPED

White

Common

Com

Black

High

Cool

Yellow

Med-High

Park

Blue

Med-High

High-Gas-Heat

Red

Low*

Low-Gas-Heat

* Continuous fan speed.

Recheck the temperature rise. It must be within the limits
specified on the unit rating plate. Recommended operation is
at midpoint of rise range or above.

16

«
...
14
15
16
17
18
»

Содержание 58TMA



















Отзывы:

Нет отзывов