BEFORE OPERATION
BEFORE OPERATION
FLAP CONTROL BUTTON
Controls the discharge air flow direction up and down.
( Refer to p.20 ) On start up, the flaps open automatically
according to the operating mode.
If you press this button, the flap will move stepwise and
the position will be displayed. If you press this button
again, the unit operates at “SWING” mode. At operating
mode “SWING”, the flap will swing up and down
continuously.
ON/OFF TIMER AND CURRENT TIME
BUTTONS
If you set the ON and OFF times, the unit will automatically
turn on and off at the set times.
( Refer to pp.15 -16 )
If you press the CLOCK button during Timer operation,
you will see the current time for 5 seconds.
HOUR/MINUTE SETTING BUTTONS
Adjust the current time (Refer Page 11) and the on/off
times of timer operation with these buttons.
RESERVATION AND CANCEL BUTTONS
Press the RESERV. button to reserve the ON/OFF Timer and
press the CANCEL button to cancel the reserved on/off
time. ( Refer to pp.15 -18 )
EVERYDAY TIMER BUTTON
Press the EVERYDAY button and the on/off time you have
reserved will be repeated until cancelled. ( Refer to pp.15 -18 )
CURRENT TIME ADJUSTING BUTTON
Press this button to adjust the current time. ( Refer to p.11 )
RESET BUTTON
Press this button when the remote control is not operating
properly or after replacing batteries.
( Refer to p. 11 )
ADDRESS SWITCH
If you have two indoor units in the same room, you can
link one remote control with one indoor unit, and link the
other remote control with the other indoor unit.
( Refer to p.11 )
6
7
8
9
10
11
12
13
REMOTE CONTROL DESCRIPTION
Names and Functions of the Buttons
LR03(AM4)1.5V
LR03(AM4)1.5V
RST
TA
OWNER
,
S MANUAL - 8
OWNER
,
S MANUAL - 9
SLEEP
MODE
FAN
FLAP
CLOCK EVERYDAY HOUR MINUTE
RESERV.
RST
TA
TIMER
ON
OFF
CANCEL
A
SWING
A
TEMP.
ON/OFF
햲
햳
햴
햵
햶
햸
햻
햷
햹
햺
ON/OFF BUTTON
If you press this button, the unit will begin operation. Press the
button again, and operation stops. ( You can hear a receiving
beep. ) If you press this button immediately after turning off
the unit, the compressor will not operate for 3 minutes to
prevent overloading.
TEMPERATURE SETTING BUTTONS
If you set the desired room temperature, then the unit will
maintain the room temperature as set . In COOL mode, if the
room temperature is higher than the setting, the compressor
will automatically turn on to provide a cooling effect. On the
other hand, if the room temperature is lower than the setting,
the compressor will automatically turn off to stop cooling
operation. In HEAT mode, if the room temperature is lower
than the setting, the compressor will automatically turn on to
provide a heating effect. If the room temperature is higher
than the setting, the compressor will automatically turn off to
stop heating operation. However,the indoor fan will continue
to circulate air even if the compressor is turned off.
SLEEP TIMER BUTTON
Press this button to set the SLEEP timer. (Refer to p.19)
OPERATION MODE SELECTING BUTTON
Press this button to select the desired mode.
In AUTO mode, the unit will run automatically by selecting
COOL or HEAT mode according to the indoor room temperature.
In DRY mode, the microcomputer of the unit controls the indoor
fan motor and makes the outdoor unit automatically turn on
and off according to the room temperature, which causes
moisture to be removed more effectively.
In COOL mode, the unit will run at the normal cooling mode.
In FAN mode, only the indoor fan will operate at the selected
fan speed and circulate room air. In HEAT mode, the unit will
run at the normal heating mode.
1
2
3
4
햿
FAN SPEED SELECTING
BUTTON
5
Press the button to select the desired fan
speed of AUTO, LOW, MED or HIGH, and the
indoor fan will operate at the selected fan
speed.
If you select “AUTO”, the fan speed will be
controlled by the microcomputer of the unit.
햾
햽
42QG8V5404B(O/M-P)
2004.7.7, 2:40 PM
8-9