Carrier 50HCQ07 Скачать руководство пользователя

Страница: 9 / 52

ROOF MOUNT
Check building codes for weight distribution requirements.

Unit operating weight is shown in Table 2.

Table 2 — Operating Weights

Step 2 — Plan for Sequence of Unit Installation

The support method used for this unit will dictate different se-

quences for the steps of unit installation. For example, on curb-

mounted units, some accessories must be installed on the unit

before the unit is placed on the curb. Review the following for

recommended sequences for installation steps:
CURB-MOUNTED INSTALLATION
1. Install curb.
2. Install field-fabricated ductwork inside curb.

3. Install accessory thru-base service connection package

(affects curb and unit) (refer to accessory installation
instructions for details).

4. Prepare bottom condensate drain connection to suit

planned condensate line routing (refer to Step 10 — Install
External Condensate Trap and Line on page 14 for

details).

5. Rig and place unit.
6. Install outdoor air hood.

7. Install condensate line trap and piping.

8. Make electrical connections.
9. Install other accessories.

PAD-MOUNTED INSTALLATION
1. Prepare pad and unit supports.
2. Check and tighten the bottom condensate drain connection

plug.

3. Rig and place unit.

4. Convert unit to side duct connection arrangement.

5. Install field-fabricated ductwork at unit duct openings.
6. Install outdoor air hood.

7. Install condensate line trap and piping.

8. Make electrical connections.
9. Install other accessories.

FRAME-MOUNTED INSTALLATION
Frame-mounted applications generally follow the sequence for

a curb installation. Adapt the sequence as required to suit spe-

cific installation plan.

Step 3 — Inspect Unit

Inspect unit for transportation damage. File any claim with

transportation agency.
Confirm before installation of unit that voltage, amperage and

circuit protection requirements listed on unit data plate agree

with power supply provided.
On units with hinged panel option, check to be sure all latches

are snug and in closed position.

Locate the carton containing the outside air hood parts. Do not

remove carton until unit has been rigged and located in final

position.

Step 4 — Provide Unit Support

ROOF CURB MOUNT
Accessory roof curb details and dimensions are shown in

Fig. 5. Assemble and install accessory roof curb in accordance

with instructions shipped with the curb.
Curb should be level. This is necessary for unit drain to func-

tion properly. Unit leveling tolerances are shown in Fig. 6. Re-

fer to Accessory Roof Curb Installation Instructions for addi-

tional information as required.
Install insulation, cant strips, roofing felt, and counter flashing

as shown.

Ductwork must be attached to curb and not to the

unit. The accessory thru-the-base power connection package

must be installed before the unit is set on the roof curb.

If electric and control wiring is to be routed through the base-

pan, attach the accessory thru-the-base service connections to

the basepan in accordance with the accessory installation in-

structions.
NOTE: The gasketing of the unit to the roof curb is critical for a

watertight seal. Install gasket supplied with the roof curb as shown

in Fig. 5. Improperly applied gasket can also result in air leaks and

poor unit performance.
SLAB MOUNT (HORIZONTAL UNITS ONLY)
Provide a level concrete slab that extends a minimum of 6 in.

(150 mm) beyond unit cabinet. Install a gravel apron in front of

condenser coil air inlet to prevent grass and foliage from ob-

structing airflow.
NOTE: Horizontal units may be installed on a roof curb if

required.
ALTERNATE UNIT SUPPORT (IN LIEU OF CURB OR

SLAB MOUNT)
A non-combustible sleeper rail can be used in the unit curb

support area. If sleeper rails cannot be used, support the long

sides of the unit with a minimum of 3 equally spaced 4-in. x

4-in. (102 mm x 102 mm) pads on each side.

50HCQ

UNIT LB (KG)

A,D07

D08

D09

Base Unit

710 (322)

875 (397)

1020 (463)

Economizer
Vertical

80 (36)

Horizontal

105 (48)

Powered Outlet

32 (15)

Curb
14 in. (356 mm)

110 (50)

24 in. (610 mm)

145 (66)

Содержание 50HCQ07





















































Результаты поиска

Содержание 50HCQ07

Отзывы:

Похожие инструкции для 50HCQ07

Бренды по названию

Популярные бренды

Carrier 50HCQ07, Руководство по установке

Результаты поиска

Содержание 50HCQ07

Отзывы:

Похожие инструкции для 50HCQ07

Бренды по названию

Популярные бренды