background image

9

WIRED REMOTE CONTROLLER (NON-PROGRAM-

MABLE) — To connect non-programmable wired remote

controller (thermostat) to the indoor unit, use 5-core shielded

cable and 5-pin connector from unit display panel (see Fig. 10).

For setup instructions, refer to  the  controller  installation

manual.

CENTRAL CONTROLLER —   The  central  controller  is

connected to the indoor unit through outdoor unit with 3-core

shielded cable (see Fig. 11). For setup instructions, refer to the

controller installation manual.

START-UP

Pre-Start Check — 

Once installation is complete, make

the following pre-start checks:

1. All indoor and outdoor units are properly installed.
2. All piping and insulation is complete.
3. All electrical connections (both power and control) are

properly terminated.

4. All condensate drains are installed correctly.
5. The power supply is of the right voltage and frequency. 
6. The units are properly grounded in accordance with cur-

rent electrical codes. 

7. Suction and liquid line service valves are in open posi-

tion.

Drain Pump and Drainage Test  — 

 Follow these

steps to perform the test:

1. Remove the test cover by rotating it counter-clockwise as

shown in Fig. 12.

2. Using a piece of tubing or pipe, fill the drain pump reser-

voir with 70 oz. of water. See Fig. 13.

3. Turn the unit ON in cooling mode. The pump comes on.

Watch the end of the drain pipe for any water. It may take

some time for the water to travel, depending on the length

of the drain pipe.

4. During this test, check any bends or joints for leakage.

WIRED REMOTE 
CONTROLLER

4-PIN CONNECTOR
FROM ELECTRICAL BOX

INDOOR

UNIT

a40-1726

Fig. 9 — Wired Remote Controller

(Programmable) Wiring

INDOOR UNIT
DISPLAY PANEL

5-CORE CABLE

5-CORE SHIELDED CABLE

INDOOR UNIT
ELECTRIC CONTROL BOX

INDOOR UNIT
ELECTRIC CONTROL
PANEL

WIRED CONTROLLER

BACK

A40-1714

5-CORE CABLE

Fig. 10 — Wired Remote Controller

(Non-Programmable) Wiring

X Y E F1 F2 E

FORCED ON EMG. STOP

R

C

TO INDOOR UNIT

X,Y,E

DAISY CHAIN

NOT USED

FORCED
ON
SWITCH

EMERGENCY
STOP
SWITCH

24 VAC

a40-1774

Fig. 11 — Central Controller (Back)

C L O S E D 

P E 

L O 

S E

 D 

O P E N 

TEST COVER

A40-1853

Fig. 12 — Test Cover

Содержание 40WAD007













Отзывы: