8
TIMER FUNCTION
TIMER ON (to start the unit) and TIMER OFF (to stop the unit)
can be used separately or together.
Timer ON only
This function allows the unit to start automatically at the set time.
The TIMER ON can be set while the unit is on or off.
UNIT ON
a. Press the TIMER ON
button to initiate the auto-on time
sequence. The set time is displayed in the remote control
display. Every time the TIMER ON button is pressed, the
time increases by 30 minutes, up to 10 h. It increases by 60
minutes, afterwards, until the time setting reaches 24 h.
b. When the TIMER ON is set, the TIMER light on unit
illuminates. The unit continues to run at the set time.
UNIT OFF
a. Set the timer described in the UNIT ON section.
b. The unit starts at the set time.
Adjust the TIMER ON settings to 0.0 to cancel this option.
Timer OFF only
This function allows the unit to stop automatically at the set time.
The timer can be set while the unit is on or while it is off.
UNIT ON
a. Press the TIMER OFF
button to initiate the auto--off time
sequence. The set time appears on the remote control display.
Every time the TIMER OFF button is pressed, the time
increases by 30 minutes, up to 10 h. It increases by 60
minutes, afterwards, until the time settings reach 24 h.
b. When the TIMER OFF is set, the timer light on the unit
illuminates and the unit turns off automatically at the set time.
UNIT OFF
a. Set the TIMER off as described in the UNIT ON section.
The TIMER display on the unit illuminates and the unit
remains off.
b. Adjust the TIMER ON settings to 0.0 to cancel this option.
Timer ON and Timer OFF
Use both functions to program the unit to turn on and shut off at
specified times.
UNIT OFF
a. Set TIMER ON as previously described.
b. Set TIMER OFF as previously described. The unit starts
automatically at the set TIME ON and turns off at the set
TIME OFF.
UNIT ON
a. Set TIME OFF as previously described.
b. Set TIME ON as previously described. The unit turns off
automatically at the set TIME OFF and turns on at the set
TIME ON.
Sleep Mode
SLEEP mode is used to conserve energy and can be used when the
unit is in the COOL, HEAT or AUTO mode only.
Cool Mode
a. Push the SLEEP button. After 1 hour the set point raises
by 1.8
_
F (1
_
C). After another hour, the set point raises by
another 1.8
_
F (1
_
C) and the fan runs in a low speed. The
unit shuts off 5 hours after setting the SLEEP mode. The
SLEEP mode cancels if either the “Mode”, “TEMP”,
“Fan”, “Timer”, or “On/Off” buttons on the remote control
is pressed.
Heat Mode
Same as cooling mode however set points are lowered by 1.8
_
F
(1
_
C).
Turbo Mode
Use the TURBO mode to cool or heat the room rapidly.
a. Press the TURBO button. An audible “beep” is heard if the
indoor unit supports this function. The fan runs on super high
speed. The TURBO mode terminates automatically 20
minutes after pushing the Turbo mode button. It can be
terminated immediately by selecting the Turbo mode again.
When the Turbo mode is terminated, the unit reverts to the
original setting.
Self Clean Mode
Press the “Self Clean” button to activate or deactivate the
self--cleaning function. Under this function, the air conditioner
automatically cleans and dries the evaporator. The cleaning cycle
takes 30 minutes, after which the unit turns off automatically. Press
SELF CLEAN
on the middle of the cycle cancels the operation
and turn off the unit. This function can be activated only on
COOL or DRY mode.
Follow Me Mode
Press the “Follow Me” button to activate or deactivate this
function. Under this setting, the temperature that appears in the
remote control is the actual temperature at its location. The remote
control sends this signal to the air conditioner every 3 minutes.
This function is not available for DRY and FAN modes.
Freeze Protection Mode
Press the “FP” button for approximately 2 seconds to activate or
deactivate the freeze protection mode (heating set back). The
indoor unit displays “FP”.
NOTE: This function is only available in the heating mode.
Under this function, the unit operates at high fan speed and the coil
temperature automatically sets to 46
_
F (8
_
C). This mode can also
be deactivated by pressing the “On/Off”, “Sleep”, “Mode”, “Fan”,
or either “TEMP” buttons.
Silence Mode
NOTE: The Silence Mode (SLC Button) is not available on this
model.
LED Light
Press the LED button to turn the display light on and off.
Resetting the Remote Control
If the batteries in the remote control are removed, the current settings
will be cancelled and the control returns to the initial settings and will
be in standby mode. Push the ON/OFF button to activate it.
Time Delay
If the On/Off button is pressed too soon after a stop, the
compressor will not start for 3 to 4 minutes due to the inherent
protection against frequent compressor cycling. The unit only
emits an audible beep when the signals are received correctly.
Heating Features
If the unit is in the heating mode, there is a delay when the fan
starts. The fan starts only after the coil is warmed up to prevent
cold blow.
Auto Defrost Operation
In heating mode, if the outdoor coil is frosted, the indoor fan and
outdoor fan turns off while the system removes the frost on the
outdoor coil. The system automatically reverts to normal operation
when frost is removed from the outdoor unit.
Auto Start
If the power fails while the unit is operating, the unit stores the
operating condition, and it will start operation automatically under
those conditions when the power is restored.