Carrier 39HXC Скачать руководство пользователя

Страница: 47 / 64

7.5 - Diagnostics

Fault

Sources

Causes

Solutions

Powered down

The power supply has been cut

The circuit breaker has been

triggered

Check the wiring and the components

Voluntary stop

Empty

Fire protection

The "fire protection" contact has

been triggered

Triggered by the fume detector or by

the external fire contact managed by

the operator

Check the condition of the contacts

Frost protection

The supply air temperature sensor

detects a temperature below

threshold P248

(4°C by default)

The air temperature at the outlet for

the

1st hydraulic coil is too cold

Check the operation of the first coil:

valve jammed, no flow, no hot water, etc.

Intake EC motor

An EC motor is indicating a fault

Overvoltage, motor overload, motor

power supply problem, etc.

Check the condition of the intake

motor(s)

Exhaust EC motor

Check the condition of the exhaust

motor(s)

Intake air flow low limit

Extraction air flow low limit

The air flow rate is below the fixed

limit P111

The air passage is blocked

Check the pressure drops and ensure

there are no foreign bodies in the ducts

and

the unit

The pressure measurement sensor

is defective

Check the operation of the sensor

Constant pressure control: the

pressure drops in the network are

too great

Check the opening/closing of the duct

network dampers

Intake filter 1 fouled

The pressure drop in the filter is

greater than the "filter fouled"

threshold

The filter is dirty

Schedule replacement of the filter before

it becomes clogged

Exhaust filter 1 fouled
Intake filter 1 blocked

The filter pressure drop is greater

than the "filter blocked" threshold

The filter is blocked

Replace the filter

Exhaust filter 1 blocked
Intake flow rate pressure

sensor

The pressure sensor signal is less

than 0.5 V

The sensor is faulty

Replace the sensor

Extraction filter pressure

sensor

Intake flow rate pressure

sensor

Incorrect connection

Check the electrical connection and

tightness of the connections

Exhaust flow rate pressure

sensor
Heat recovery unit pressure

sensor
Rotary heat exchanger

The rotary heat recovery unit

indicates a fault

The heat recovery unit controller has

detected a fault

Check the operation of the heat recovery

unit and the condition of the belt

Heat recovery frosted

The pressure drops measurement

for the heat recovery unit is greater

345 Pa

Operating problem with the

differential pressure sensor

Check the operation of the sensor

The heat recovery unit is clogged

Clean the heat recovery unit

The heat recovery unit is frozen

Wait for the heat recovery unit to be

defrosted

Electric heater safety

thermostat

One of the safety thermostats for an

electric heater has been tripped

The temperature in the electric

heater is greater than the thermostat

limit (80 °C)

Check that the air flow is sufficient and

check the condition of the switches and

the electric heater

Intake duct pressure too low

The duct pressure is below the fixed

limit P124

Operating problem with the intake

pressure sensor

Check the operation of the sensor

Operating problem with the FMAs

Check the maximum frequency of the

inverter/motor and check that the motor

turns correctly

Intake duct pressure too high

The duct pressure is above the fixed

limit P125

Operating problem with the intake

pressure sensor

Check the operation of the sensor

Operating problem with the FMAs

Check the maximum frequency of the

inverter/motor

Exhaust duct pressure too low

The duct pressure is below the fixed

limit P142

Operating problem with the intake

pressure sensor

Check the operation of the sensor

Operating problem with the FMAs

Check the maximum frequency of the

inverter/motor and check that the motor

turns correctly

Exhaust duct pressure too

high

The duct pressure is above the fixed

limit P143

Operating problem with the intake

pressure sensor

Check the operation of the sensor

Operating problem with the FMAs

Check the maximum frequency of the

inverter/motor

7 - FAULTS

Содержание 39HXC

































































Результаты поиска

Содержание 39HXC

Отзывы:

Похожие инструкции для 39HXC

Бренды по названию

Популярные бренды

Carrier 39HXC, Руководство пользователя

Результаты поиска

Содержание 39HXC

Отзывы:

Похожие инструкции для 39HXC

Бренды по названию

Популярные бренды