manualshive.com logo in svg

Carrier 024-036, Руководство по обслуживанию, Страница: 2 / 41

Поделиться
Скачать
Carrier 024-036 Скачать руководство пользователя страница 2

: Service Manual

Manufacturer reserves the right to change, at any time, specifications and designs without notice and without obligations.

2

part numbers and related pre-sale data.  Installation Instructions are also

available per specific models.
Information in this document refers to units produced in 2010 to current.

Installation Guideline

Residential New Construction

Specifications for these units in the residential new construction market

require  the  unit  to  be  installed  outdoors  and  meet  all  local  code  and

requirements.  Consult  the  Installation  Instructions  for  any  additional

installation detail.

Add-On Replacement (Retrofit)

Specifications for these units in the add-on replacement/retrofit market

require  the  unit to be  installed outdoors and meet  all local  codes  and

requirements. Clearances, power supply, system static needs to be check

to  ensure  that  the  replacement  unit  can  perform  within  the  design

parameter desired specified in the Product Data.

Accessories

Accessory Descriptions

Refer to 

Table 1

 for an Accessory Usage Guide for Air Conditioners and

Heat Pumps. Refer to the appropriate section below for a description of

each accessory and its use.

1. Crankcase Heater

An  electric  resistance  heater  which  mounts  to  the  base  of  the

compressor to keep the lubricant warm during off cycles. Improves

compressor  lubrication  on  restart  and  minimizes  the  chance  of

liquid slugging.

Usage Guideline:

Required in low ambient cooling applications.

Suggested in all commercial applications.

2. Evaporator Freeze Thermostat

An  SPST  temperature-actuated  switch  that  stops  unit  operation

when evaporator reaches freeze-up conditions.

Usage Guideline:

Required when low ambient kit has been added.

3. Isolation Relay

An SPDT relay which switches the low-ambient controller out of

the  outdoor  fan  motor  circuit  when  the  heat  pump  switches  to

heating mode.

Usage Guideline:

Required in all heat pumps where low ambient kit has been 

added

4. Outdoor Thermostat Kit

Locks  out  the  accessory  electric  heater  until  outdoor  ambient

conditions falls below the pre-set temperature. This kit will activate

the electric heat when additional heat is required at lower ambient

making it a more efficient system.

Low-Ambient Cooling Guideline

The minimum operating temperature for these units in cooling mode is

40°F/4.4°C  outdoor  ambient  without  additional  accessories.  This

equipment  may  be  operated  in  cooling  mode  at  ambient  temperatures

below 40°F/4.4°C when the accessories listed in 

Table 1

 are installed. 

Table 1 – Required Field-Installed Accessories for Air Conditioners 

and Heat Pumps

Accessory 

Required for low 

ambient cooling

applications

(Below 40°F / 

4.4°C)

Accessory Part

Number

Motormaster II Low 

Ambient Kit

Yes

CPLOWAMB001A00

Evaporator Freeze

Thermostat

 Recommended

KSAFT0101AAA

Compressor Start Assist 

(CTCR)

Yes

CPHSTART002A00

Isolation Relay (Required 

for Heat Pumps)

Yes

--HN--65KJ-016

 Crankcase Heater

--

See below...

 -- AC 13.4 SEER2 24-36

Yes

CPCRKHTR007A00

 -- AC 13.4 SEER2 42-60

Yes

CPCRKHTR004A00

-- HP 13.4 SEER2 42-60
-- HP 13.4 SEER2 24-36

Yes

CPCRKHTR008A00

Содержание 024-036










































Отзывы:

Нет отзывов