background image

3

www.CarnivalKingSupplies.com   

.

   ||||| [email protected]

Manual

Installation and Operation Instructions

1. Place the sno-cone machine in a place where it cannot be pushed off the counter.
2. Keep the area at the front of the sno-cone clear for unobstructed access during operation.
3. Keep unit and power cord away from open flames, electric burners or excessive heat.
4. Do not use an extension cord with this equipment.
5. Install the handle assembly/ice pusher on top of the machine, install the ice tray and the drain valve.  
    Install cup dispenser.
6. Ensure that the ice blades are free of any obstructions, connect the power cord to the machine and plug it into a 

    grounded 120V outlet. 

 

Operation 

1. Open the door and wipe the tempered glass cabinet with a dry cloth, check that the blade is firmly installed.
2. Open the handle assembly/ice pusher and fill the horn with the desired amount of either cube or chunk ice, do not 

overfill.
3. Close the handle assembly/ice pusher and please ensure that the machine is on a level stable surface, the feet are 

intact and level.
4. Press the switch to start the unit, depress the handle to push the ice cubes through the blade.

Ice Shaver Machine Specs

Item #

382SCM350R

Overall Dimensions

16

¼

"W x 14

¼

"D x 27½"H

Cabinet Size

16

¼

”W x 14

¼

”D x 19”H

Cabinet Material

Tempered Glass

Horn Material

Die-Cast Aluminum

Horsepower

1/3 HP

RPM

1700RPM

Capacity

500 lbs. Per Hour

Wattage

350W

Voltage

120V

Amps

2.8 Amps

Hertz

60Hz

Phase

1

Plug

NEMA 5-15P

Function and Purpose

This unit is intended to be used for shaving and crushing ice in commercial foodservice operations only. It is not 

intended for household, industrial, or laboratory use.
Before using this equipment, it must be cleaned and 

dried thoroughly

. Clean all surfaces before use. Failure to clean 

surfaces before using the unit could cause food contamination.
This ice crusher is intended for crushing ice cubes for use in sno-cones, ice cubes should be a maximum of 2 inches 

in diameter. Larger pieces should be broken up before processing through the machine. Your sno-cone machine can 

produce up to 500 lbs. of ice per hour, or about 1000 6 oz. sno-cones per hour. This Royalty Series sno-cone machine 

includes a cup dispenser that fits up-to 8 oz. sno-cone cups.

Содержание ROYALTY Series









Отзывы: