Carlton A1EP-GL Скачать руководство пользователя страница 10

Страница: 10 / 48

Carlton

Maintenance and Safety Manual

Saw Chain Components

Saw chain pitch

The word

pitch

actually means size. The larger the pitch

(measured in thousandths of an inch) the larger the saw chain.

Pitch is determined by measuring the distance between the

centerlines of three consecutive rivets and dividing this distance

in half. In other words, 3/8" pitch saw chain (.375") measures

3/4" (.750") between the centerlines.

Saw chain gauge

Gauge

refers to the thickness of

the drive link tangs that fit into

the guide bar groove and is also

measured in thousandths of an

inch. There are four standard

gauges for hand held chain saw

cutting chain: .043", .050", .058"

and .063". It’s essential for the

saw chain’s gauge to match the

guide bar gauge.

Carlton

Technical Tip

1. Saw chain pitch must match the pitch of the drive sprocket

and the guide bar sprocket tip.

2. Saw chain gauge must match the gauge of the guide bar.

Any mismatch of the chain saw parts will lead to premature

failure of the saw chain, guide bar, or drive sprocket.

This distance divided by 2

1.1 mm

.043"

Tang

.050" 1.3 mm

.058" 1.5 mm

.063" 1.6 mm

Содержание A1EP-GL

















































Результаты поиска

Содержание A1EP-GL

Отзывы:

Похожие инструкции для A1EP-GL

Бренды по названию

Популярные бренды

Carlton A1EP-GL, Инструкция по техническому обслуживанию и безопасности

Результаты поиска

Содержание A1EP-GL

Отзывы:

Похожие инструкции для A1EP-GL

Бренды по названию

Популярные бренды